K2theStank 🇨🇦
RRCRat Rig Community [Unofficial]
•Created by celestial_avocado_45840 on 3/14/2025 in #fix-my-printer
layershifting Problems
I had to down speed my IDEX by almost 1/3 of performance to get the IDEX working properly and it's only 75% there. I'm get to a Max of 4k acceleration and 250mm/s
I'm incredibly disappointed with the machine and how hard it is to even get a consistent print
10 replies
RRCRat Rig Community [Unofficial]
•Created by njneer on 3/12/2025 in #fix-my-printer
Bed/Gantry Leveling VCore 4 IDEX 500
They say to have Xmm from top to mid rail you can make a block that's that size to help ensure they are all the exact size
10 replies
RRCRat Rig Community [Unofficial]
•Created by Simon on 2/18/2025 in #fix-my-print
3 good layers then no succesful print
i have been doing a ton of work and testing to determine an optimal tension to speed optimization settings
tools used:
- BIQU Belter /w printed tip
Machine:
- RatRig vCore4 400mm IDEX
Findings:
- 10k acceleration and 600mm/s is where the issue seems to arise where the toolheads will move at high speeds off their X0/X1 homes when rapidly moving the Y axis
Solution findings:
- Using the BIQU Belter adjusting all belts while in the 0 position to -6.5 to -7.1 ensuring they all match
- by reducing the max accel to 8k and max speeds to 500mm/s the X0/X1 jerking motions seem to have been eliminated though more testing is required
While i dont have a Hz measurement tool these settings seem to have helped in the machines consistent movements
16 replies
RRCRat Rig Community [Unofficial]
•Created by Simon on 2/18/2025 in #fix-my-print
3 good layers then no succesful print
Printing too fast for a vCore4 IDEX here is a setting i use that helps, spent hours running speeds and acceleration to get consistent prints
16 replies
RRCRat Rig Community [Unofficial]
•Created by njneer on 3/12/2025 in #fix-my-printer
Bed/Gantry Leveling VCore 4 IDEX 500
I printed a 3D block that's the right size and used it as a reference for when i was tightening mine it might help
10 replies
RRCRat Rig Community [Unofficial]
•Created by K2theStank 🇨🇦 on 3/6/2025 in #fix-my-printer
Why is my Z-Tilt only hitting 2 of 3 corners
17 replies
RRCRat Rig Community [Unofficial]
•Created by Andrii on 3/3/2025 in #fix-my-printer
Move Out of Range Error When Measuring T1 Belt Tension
mine also just started doing this spent all day testing my tension and now i get the same errors
3 replies
RRCRat Rig Community [Unofficial]
•Created by K2theStank 🇨🇦 on 3/6/2025 in #fix-my-printer
Why is my Z-Tilt only hitting 2 of 3 corners
its been solved i apparently had the Y1 belt wrapped around the standoff behind the bearing 🙂
17 replies
RRCRat Rig Community [Unofficial]
•Created by K2theStank 🇨🇦 on 3/6/2025 in #fix-my-printer
Why is my Z-Tilt only hitting 2 of 3 corners
I have moved it to the set-up phase and manually lowered the speeds
17 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 3/2/2025 in #fix-my-printer
What is this click moving x axis? A dead bearing?
I also have this sound and been poking at it almost all day with no resolution
16 replies
RRCRat Rig Community [Unofficial]
•Created by K2theStank 🇨🇦 on 3/6/2025 in #fix-my-printer
Why is my Z-Tilt only hitting 2 of 3 corners
homing and Z-Tilt at 150 work but the moment you speed up the printer T0 and T1 crash into each other and/or the gantry walls similiar as the video only WAYYYY faster which has now broken the T1 endstop from a 600mm/s slaming into the side wall
17 replies
RRCRat Rig Community [Unofficial]
•Created by K2theStank 🇨🇦 on 3/6/2025 in #fix-my-printer
Why is my Z-Tilt only hitting 2 of 3 corners
17 replies