Wetson
RRCRat Rig Community [Unofficial]
•Created by im2fast4you4. on 3/28/2025 in #fix-my-printer
nternal error during connect: module 'extras.resonance_tester' has no attribute 'SweepingVibrationsT
You need to update your RatOs
3 replies
RRCRat Rig Community [Unofficial]
•Created by nathanjenny on 4/1/2025 in #fix-my-printer
Filament sensor always switches to detected after prime blob. I have tried everything and am stuck.
This is most likely due to the filament tangle sensor on the filament sensor. You can either disable it in configuration or pull the yellow wire from the sensor
3 replies
RRCRat Rig Community [Unofficial]
•Created by jcase on 4/18/2025 in #fix-my-printer
Layer shifting during Skew Calibration Print - VC4 400mm IDEX
Have you activated performance mode?
4 replies
RRCRat Rig Community [Unofficial]
•Created by Petru on 4/15/2025 in #fix-my-printer
Unloading during printing
This is due to false-positives from the tangle sensor on the filament sensor. You can disable in the config or by pulling the yellow wire from the toolboard.
3 replies
RRCRat Rig Community [Unofficial]
•Created by Growlix on 4/10/2025 in #fix-my-printer
Fan speed problems during toolchange
orca slicer is not officially supported to be compatible with IDEX, this may be where your problem is coming from. However your fan speeds should be set per material in your slicer.
Did you follow this guide for setting up the gcode pre-sets in your slicer?
https://os.ratrig.com/docs/slicers/
3 replies
RRCRat Rig Community [Unofficial]
•Created by Tachyon on 4/10/2025 in #fix-my-printer
Advice sought; Trying to tune TMC2209
TMC2209 is controlled via RatOs for current. Although I am unsure that the potentiometer gets overriden, there is no need. Use RatOs to change current. However, the default settings in "performance" mode should be 100% adequate on a stock steup
3 replies
RRCRat Rig Community [Unofficial]
•Created by Tachyon on 4/12/2025 in #fix-my-printer
TMC 'extruder' reports error: GSTAT: 00000001 reset=1(Reset)
OTP flags on Z1 and Z2 means cooling is not sufficient for your drivers, no?
Swap the board between T1 and T0, see if it continues. If it stops, consider the board dead.
3 replies
RRCRat Rig Community [Unofficial]
•Created by AceMan on 4/15/2025 in #fix-my-printer
Filament detector doesn't seem to act properly
Should take a multimeter to the orbiter sensor and check that it's actually actuating. I had to dissassembly mine due to junk being in the VERY tiny micro switch. Works great now!
40 replies
RRCRat Rig Community [Unofficial]
•Created by celestial_avocado_45840 on 3/14/2025 in #fix-my-printer
layershifting Problems
Belt tension and assembly quality, depending on your size this isn't all that bad of numbers however.
10 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
Nice job finding the fix :)
302 replies
RRCRat Rig Community [Unofficial]
•Created by Ibot on 1/24/2025 in #fix-my-print
IDEX XY Offset drift (VC4)
4th having drift... Check your tension again. I've had the tension "settle" after tightening once. Needed to be redone after a few prints :) hopefully it's that easy...
657 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
Also, you should paste above that section
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
Balena gave me severe issues as well
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
Looks normal
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
My only other suggestion is reinstalling ratos but that feels a bit nuclear so 😂
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
Everything up to date in ratos?
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
Yes
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
Ah ok
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
Lemme find the link
302 replies
RRCRat Rig Community [Unofficial]
•Created by Chris on 3/22/2025 in #ratos-support
Mirror/Copy mode and cancel print not working
DC endstop calibration is part of the VAOC calibration steps
302 replies