Animatrix
Animatrix
PostsComments
RRCRat Rig Community [Unofficial]
Created by C7H on 8/31/2023 in #fix-my-mesh
Bed Compensates Too much
But a probe one mainly
15 replies
RRCRat Rig Community [Unofficial]
Created by C7H on 8/31/2023 in #fix-my-mesh
Bed Compensates Too much
As exoected
15 replies
RRCRat Rig Community [Unofficial]
Created by C7H on 8/31/2023 in #fix-my-mesh
Bed Compensates Too much
It was a mesh issue
15 replies
RRCRat Rig Community [Unofficial]
Created by C7H on 8/31/2023 in #fix-my-mesh
Bed Compensates Too much
I fixed my issue
15 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
No description
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
klicky
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
// probe accuracy results: maximum 2.632000, minimum 2.631062, range 0.000937, average 2.631687, median 2.631687, standard deviation 0.000280 10 samples
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
10 samples
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
// probe accuracy results: maximum 2.633562, minimum 2.632000, range 0.001562, average 2.632969, median 2.632937, standard deviation 0.000406
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
// probe accuracy results: maximum 2.652937, minimum 2.650437, range 0.002500, average 2.652525, median 2.652625, standard deviation 0.000557 25 samples
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
[bed_mesh]
horizontal_move_z: 5
mesh_min: 20,20
mesh_max:465,460
probe_count: 8,8
fade_start: 3.0
fade_end: 0.0
mesh_pps: 2,2
algorithm: bicubic
bicubic_tension: .2

[z_tilt]
z_positions:
    0,0
    250,500
    500,0

points:
    40,35
    280,470
    465,20
        
horizontal_move_z: 20
retries: 10
retry_tolerance: 0.02
[bed_mesh]
horizontal_move_z: 5
mesh_min: 20,20
mesh_max:465,460
probe_count: 8,8
fade_start: 3.0
fade_end: 0.0
mesh_pps: 2,2
algorithm: bicubic
bicubic_tension: .2

[z_tilt]
z_positions:
    0,0
    250,500
    500,0

points:
    40,35
    280,470
    465,20
        
horizontal_move_z: 20
retries: 10
retry_tolerance: 0.02
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
Left rear corner - very far from plate, doesn't stick - perhaps (-)0.2mm Right rear corner - barely close, i would do -0.05 if i could Front left corner - goodW Front right corner - too close, i would add +0.1 if i could
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
while the mesh looks like that ^, it kinda feels like my whole mesh is mirrored. Im not sure how that can happen. The left rear is too far away when i actually print something and nothing sticks right while in the mesh its the right rear thats far away, perhaps it is far too.
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
no dice, all good.
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
i removed and checked all the screws, couplers
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
its almost like the probe isn't doing anything
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
i've tried altering the points
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/9/2024 in #fix-my-mesh
Extremely terrible mesh, bad tilt
firstly, the tilt is not even right
22 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/1/2024 in #fix-my-mesh
tilt even after Z_TILT_ADJUST and a very fine bed mesh
same with the rails
12 replies
RRCRat Rig Community [Unofficial]
Created by Animatrix on 4/1/2024 in #fix-my-mesh
tilt even after Z_TILT_ADJUST and a very fine bed mesh
clean the oldham couplers and check if they're smooth
12 replies