Budz (PD3D)
RRCRat Rig Community [Unofficial]
•Created by vimja on 3/29/2025 in #fix-my-print
v-core 4 dragging nozzle through print
That’ll do it lol
13 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 3/31/2025 in #fix-my-printer
VAOC IDEX Calibration toolhead collision.
almost looks like the pulleys were slipping or something.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 3/31/2025 in #fix-my-printer
VAOC IDEX Calibration toolhead collision.
weirdd, im running mine at 2.6A
6 replies
RRCRat Rig Community [Unofficial]
•Created by vimja on 3/29/2025 in #fix-my-print
v-core 4 dragging nozzle through print
80% is likely too low.
13 replies
RRCRat Rig Community [Unofficial]
•Created by vimja on 3/29/2025 in #fix-my-print
v-core 4 dragging nozzle through print
My extrusion multiplier usually ranges from 85-95% depending on filament.
13 replies
RRCRat Rig Community [Unofficial]
•Created by vimja on 3/29/2025 in #fix-my-print
v-core 4 dragging nozzle through print
Sounds like overextrusion.
13 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 12/27/2024 in #fix-my-print
First layer Perfect everything after that is garbage
What do you had flowrate set to? Looks likes you’re outrunning the hotend on the flow test
19 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 8/21/2024 in #fix-my-print
Ripple in Pressure Advance Tower
Try lower temps or more cooling.
8 replies
RRCRat Rig Community [Unofficial]
•Created by Naiofz91 on 8/8/2024 in #fix-my-print
1'st layer issue
Also what kinda of filament, temps, speeds etc.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Naiofz91 on 8/8/2024 in #fix-my-print
1'st layer issue
What’s your mesh look like when heated?
5 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/24/2024 in #fix-my-print
Consistent gaps between walls with proper EM and PA on VC4-400 hybrid.
Guessing it’s slightly under extruding though.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/24/2024 in #fix-my-print
Consistent gaps between walls with proper EM and PA on VC4-400 hybrid.
What’s your smooth time?
15 replies
RRCRat Rig Community [Unofficial]
•Created by Supercrossed on 8/17/2024 in #fix-my-print
vcore 3.1 PACF woes
You need to tune every filament, PA is very sensitive to moisture and needs to be dried even out of the bag half of the time.
8 replies
RRCRat Rig Community [Unofficial]
•Created by Decker on 8/18/2024 in #fix-my-printer
Consistent Jams With Chube
Just sayin may not be enough surface area without
78 replies
RRCRat Rig Community [Unofficial]
•Created by Decker on 8/18/2024 in #fix-my-printer
Consistent Jams With Chube
You for sure need the fan.
78 replies
RRCRat Rig Community [Unofficial]
•Created by fish on 8/1/2024 in #fix-my-print
worbling on layer 2 (ASA)
Not adhere so to say you can cut it with a razor blade easily.
15 replies
RRCRat Rig Community [Unofficial]
•Created by fish on 8/1/2024 in #fix-my-print
worbling on layer 2 (ASA)
Rtv silicone can be good for sealing too:)
15 replies
RRCRat Rig Community [Unofficial]
•Created by fish on 8/1/2024 in #fix-my-print
worbling on layer 2 (ASA)
Probably need to seal up the cracks in the chamber better. Have you dried the filament?
15 replies
RRCRat Rig Community [Unofficial]
•Created by fish on 8/1/2024 in #fix-my-print
worbling on layer 2 (ASA)
Try 35% fan.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 7/20/2024 in #fix-my-printer
very inconsistent first layers on VC4
Does yours not do the wipe at 150 already? In front left
11 replies