El Pollo Macho
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
Instead of banging my head against the wall on this, I decided to wire PWM to the Octopus, and carry the weight of the extra wire
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
pretty stumped here, am I perhaps missing some step in setting up the EBB that is controlling the PWM signal? I bought these directly from the manufacturer, so it has the stock settings
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
I've now hooked up the Mechatronics fan, jumpered to 24V, and it behaves the same way as the fan I have installed: no movement 0-99%, switches on at 100%
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
I've put in an order for a Mechatronics 4028 24V Fan (MH4028H24B1+6-RSR), if that is not immediately compatible, I'll see if I can find the specs to the old one I have assembled
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
If the fan is old or incompatible, I'm also fine to change it
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
No luck, fan still only activates at 100%, any other input and it stays off
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
This is my old config file, from before the rebuild, if it helps
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
Figured it out 🙂
17 replies
RRCRat Rig Community [Unofficial]
•Created by El Pollo Macho on 7/26/2024 in #fix-my-printer
4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1
Excuse my ignorance, how do I get that? Are they the klipper logs?
17 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 7/20/2024 in #ratos-support
pullup_resistor :ERROR
2.1
61 replies