Pad
Pad
PostsComments
RRCRat Rig Community [Unofficial]
Created by Flo@GRNbms on 12/15/2024 in #fix-my-print
First layer problem
The first layer on mine is also very meh... I am also Limited to smaller prints because prints over the entire bed are so unreliable. Worst experience ever compared to any of my 4 other printers...
84 replies
RRCRat Rig Community [Unofficial]
Created by Tavidar on 12/17/2024 in #fix-my-print
Extrusion flow issue VCore 4
Therefore on my T0 the shown 210 C were closer to 230. After reducing my temp to 190 on T0 I got a good benchy just like on T1 with the same filament at 210 C
7 replies
RRCRat Rig Community [Unofficial]
Created by Tavidar on 12/17/2024 in #fix-my-print
Extrusion flow issue VCore 4
Hey, I had a similar problem. I am using an IDEX version and couldn't figure out why one Tool head produced a perfect benchy while the other one looked similar to yours. I narrowed it down to the print temperature. The Rapido hotends seem to have a really large temperature reading delta.
7 replies
RRCRat Rig Community [Unofficial]
Created by boinappi on 12/16/2024 in #fix-my-print
Smudgy/ripply top layers & solid infill
Reduces it for testing to 100mm/s max and got a perfect top layer
16 replies
RRCRat Rig Community [Unofficial]
Created by boinappi on 12/16/2024 in #fix-my-print
Smudgy/ripply top layers & solid infill
The 2nd problem afterwards were gaps + ripples. This was caused by an to high print speed (Default profile in PS is not suited for PLA @ 200mm/s lol)
16 replies
RRCRat Rig Community [Unofficial]
Created by boinappi on 12/16/2024 in #fix-my-print
Smudgy/ripply top layers & solid infill
This way my primary source for the ripples
16 replies
RRCRat Rig Community [Unofficial]
Created by boinappi on 12/16/2024 in #fix-my-print
Smudgy/ripply top layers & solid infill
I faced similar problems the past days. One of my finding is that my T0 is hotter than displayed which caused ripples on my top layers while printing at 210 C because it was actually at 230-240C. After reducing it to 190C I gor better
16 replies
RRCRat Rig Community [Unofficial]
Created by boinappi on 12/16/2024 in #fix-my-print
Smudgy/ripply top layers & solid infill
What's your print speed and your extruder temp
16 replies
RRCRat Rig Community [Unofficial]
Created by tobi0892. on 12/9/2024 in #fix-my-print
Over and underextruded solid top layer
Might be PA? I've seen that on my printer before tuning PA?
30 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
👍🏼
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
Thanks for the help 🙂
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
But still, I think it would be better to move to the endstop location before moving closer to the cam again
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
k
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
Well maybe it was user error. As I mentioned I might have been to quick on the E-stop.
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
Id say so
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
High toolhead z-offset of 0.088125mm!

Your toolhead z-offset could be better.
Use minimum 0.3mm first layer height for copy and mirror mode prints.
High toolhead z-offset of 0.088125mm!

Your toolhead z-offset could be better.
Use minimum 0.3mm first layer height for copy and mirror mode prints.
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
Its done now
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
Maybe it is better to move X/Y when the printer moved the bed down and before it moves up again to engage with the endstop. Makes it less scarry
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
It s working now. Just after my first try of running this calibration and the nozzle decided to crash into the cam (An hour ago) I was to quick on pressing the E.Stop for any of the other tries.
76 replies
RRCRat Rig Community [Unofficial]
Created by Pad on 11/9/2024 in #ratos-support
VOAC Z-Endstop calibration crashes into cam
Sorry.
76 replies