Unorthad0x Comments - Answer Overflow

Unorthad0x

•Created by Skye on 1/9/2025 in #fix-my-resonance

vc4 500 core xy for now first resonance

Itll be one of the motor pulleys. Disable motors and move the heads around one by one while watching the pulley and see if you notice sort of a bulge on one

59 replies

RRCRat Rig Community [Unofficial]

•Created by Skye on 1/9/2025 in #fix-my-resonance

vc4 500 core xy for now first resonance

If you still have the "wave like" resistance pattern when belts are tensioned and moving by hand Id bet it is a out of round motor pulley. I had the same thing and had to replace one - carefully watch the center of the pulley while moving toolhead and you will see it

59 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

True, but voron xy range is 7.5-15NM on *6MM * belts/bearings

565 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

Voron z belts are for example 20-25NM so Id think we are well within limits for the bearings

565 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

Nice! My sweet spot with the belter is 6.45mm which converts to 15.77NM or 11.63Lbs according to their calculator

565 replies

RRCRat Rig Community [Unofficial]

•Created by 03Julian04 on 11/13/2024 in #fix-my-print

Inconsistent Flow on each print/ day

[bed_mesh] horizontal_move_z: 2 mesh_min: 30,30 mesh_max:470,450 probe_count: 40,40 fade_start: 1.0 fade_end: 10.0 mesh_pps: 2,2 algorithm: bicubic bicubic_tension: .2

1455 replies

RRCRat Rig Community [Unofficial]

•Created by 03Julian04 on 11/13/2024 in #fix-my-print

Inconsistent Flow on each print/ day

There is a "phase out" from the mesh. Its referred to as fade_start and fade_end

1455 replies

RRCRat Rig Community [Unofficial]

•Created by ~ bitbash on 1/26/2025 in #fix-my-printer

Belt aligned help

7 replies

RRCRat Rig Community [Unofficial]

•Created by ~ bitbash on 1/26/2025 in #fix-my-printer

Belt aligned help

That pulley looks like its upside down

7 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

running 15-20k on everything but outer walls though

565 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

Interesting tests. On my 500 I gave up on perfect graphs and settled with 4k

565 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

Im using the ti tube

565 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

Not a 500, but cut stubbies on the end

565 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

Thats how helge runs his X

565 replies

RRCRat Rig Community [Unofficial]

•Created by Jombo on 1/23/2025 in #fix-my-printer

Printing Speeds past 150.

What is your max flowrate set at and what temp are you using for pla?

21 replies

RRCRat Rig Community [Unofficial]

•Created by MonsieurLemon153 on 1/14/2025 in #fix-my-printer

Pei sheet chipping and peeling vcore 4 500

Its not really optional with petg - you must use glue or this is what happens, especially if the z height isnt absolutely perfect. The petg fuses to the surface

13 replies

RRCRat Rig Community [Unofficial]

•Created by MonsieurLemon153 on 1/14/2025 in #fix-my-printer

Pei sheet chipping and peeling vcore 4 500

Prob the previous damage, I use glue with petg and no problems. Without glue petg will ruin most plates

13 replies

RRCRat Rig Community [Unofficial]

•Created by MonsieurLemon153 on 1/14/2025 in #fix-my-printer

Pei sheet chipping and peeling vcore 4 500

Did you use any kind of glue/release agent?

13 replies

RRCRat Rig Community [Unofficial]