Covert
RRCRat Rig Community [Unofficial]
•Created by someaction on 2/19/2025 in #fix-my-printer
camera setup logitech c920
How did you go ? I'm chasing down my own logittech camera problem atm.
38 replies
RRCRat Rig Community [Unofficial]
•Created by Covert on 4/2/2025 in #ratos-support
expected probe state to be deployed but is stowed (1) on start of print
Solved it. There is a bug in the adaptive mesh "[gcode_macro PROBE_FOR_PRIMING]" line 105 - "{% set z = printer.configfile.settings.bed_mesh.horizontal_move_z|float %}" where it doesn't account for the probe z offset. The config for my machine has a horizontal_move_z set to 5 and my probe offset is also about 5. For my fix I added "horizontal_move_z: 10" to the [bed_mesh] section (add section if not there)
7 replies
RRCRat Rig Community [Unofficial]
•Created by Covert on 4/2/2025 in #ratos-support
expected probe state to be deployed but is stowed (1) on start of print
"4:17 PM
Error evaluating 'gcode_macro _ASSERT_PROBE_STATE:gcode': gcode.CommandError: expected probe state to be deployed but is stowed (1)
4:17 PM
Error evaluating 'gcode_macro _ASSERT_PROBE_STATE:gcode': gcode.CommandError: expected probe state to be deployed but is stowed (1)
4:17 PM
Error evaluating 'gcode_macro _ASSERT_PROBE_STATE:gcode': gcode.CommandError: expected probe state to be deployed but is stowed (1)
4:17 PM
Error evaluating 'gcode_macro _ASSERT_PROBE_STATE:gcode': gcode.CommandError: expected probe state to be deployed but is stowed (1)
4:17 PM
Error evaluating 'gcode_macro _ASSERT_PROBE_STATE:gcode': gcode.CommandError: expected probe state to be deployed but is stowed (1)
4:17 PM
Error evaluating 'gcode_macro _ASSERT_PROBE_STATE:gcode': gcode.CommandError: expected probe state to be deployed but is stowed (1)
4:17 PM
Error evaluating 'gcode_macro _ASSERT_PROBE_STATE:gcode': gcode.CommandError: expected probe state to be deployed but is stowed (1)
4:17 PM
probe: TRIGGERED
4:17 PM
RatOS | Adaptive Mesh: Probing the start of the prime location at 492.05, 42.46
4:17 PM
RatOS | Adaptive Mesh: Probing the prime location..
4:17 PM
RatOS | Adaptive Mesh: bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation.
4:17 PM
Probe batch mode enabled: already deployed
4:17 PM
RatOS | Adaptive Mesh: Recieved coordinates X0=218.644 Y0=153.644 X1=281.356 Y1=346.356
4:17 PM
Probe batch mode enabled: not stowing
4:17 PM
Probe batch mode enabled: already deployed
4:17 PM
RatOS: Homing Z
4:17 PM
RatOS: Rehoming Z after Z tilt adjustment...
4:17 PM
Probe batch mode enabled: not stowing
4:17 PM
Retries: 1/10 Probed points range: 0.014297 tolerance: 0.020000"
7 replies
RRCRat Rig Community [Unofficial]
•Created by Covert on 4/2/2025 in #ratos-support
expected probe state to be deployed but is stowed (1) on start of print
7 replies
RRCRat Rig Community [Unofficial]
•Created by cereal killer on 8/23/2024 in #ratos-support
RatOS expects stowable probe to be deployed before print
Same error. Did you find a solution ?
3 replies
RRCRat Rig Community [Unofficial]
•Created by Lucky7 on 5/24/2023 in #fix-my-printer
Filament jam after/during filament change
How did you go. I have the same problem and came here from a search
5 replies
RRCRat Rig Community [Unofficial]
•Created by reduced-jade on 5/7/2023 in #fix-my-printer
Belts Binding in specific spot
Hi Len. Might not be related but I'm chasing down a similar issue. I checked my bearing stack and it was correct. I then measured the Mini Precision Shim's and found they are not so precision. 0.93mm. Moving the 2GT Timing Pulley to account for the shim error seems to have solved my end.
111 replies
RRCRat Rig Community [Unofficial]
•Created by Covert on 5/6/2023 in #fix-my-printer
Clogged hotend?
Orbiter steeper is missing steps. While extruding at 5mm/s for 50mm it becomes very obvious hearing the Stepper miss and the extruded filament shows little imperfections in time with the sound of the step missing.
Increased tmc2209 extruder current to 0.9 (was 0.35) at the end of slicer start gcode.
Unsure what's causing the restriction to the filament. Changed tube joining extruder and hotend. Removed long tube going into top of extruder.
3 replies