CoffeeSquirel
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 7/19/2024 in #ratos-support
Does RatOS RC1 flashing delete bootloader?
Got it working now, thread can be closed 🙂
7 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 7/19/2024 in #ratos-support
Does RatOS RC1 flashing delete bootloader?
Thats weird because Im unable to flash new firmware
7 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 4/5/2023 in #fix-my-printer
Printer fails to probe a bed mesh when starting a print
Red herring?
11 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 4/5/2023 in #fix-my-printer
Printer fails to probe a bed mesh when starting a print
Got a successful bed mesh on the fourth try
11 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 4/5/2023 in #fix-my-printer
Printer fails to probe a bed mesh when starting a print
Should also note that I updated the system yesterday
11 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 4/5/2023 in #fix-my-printer
Printer fails to probe a bed mesh when starting a print
The probe seems to trigger reliably between 1.49 and 1.5mm, I don't think the wiring is the problem, though it doesnt hurt to check
11 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 4/5/2023 in #fix-my-printer
Printer fails to probe a bed mesh when starting a print
Then I have to open up the electronic enclosure again.. damn
11 replies
RRCRat Rig Community [Unofficial]
•Created by extended-salmon on 12/24/2022 in #fix-my-printer
Trouble connecting PI to Octopus V1.1.... I think
When I built my V-Minion, I spent two days troubleshooting why the MCU went in shutdown everytime I tried moving any axis. Turns out RatOS checks all motor drivers for comms, and a misplaced driver was causing the issue lol
118 replies
RRCRat Rig Community [Unofficial]
•Created by extended-salmon on 12/3/2022 in #ratos-support
RatOS + BigTreeTech CB1 Pi Clone
From what I remember:
klipper_config
/printer_data/config (I think
Files inside /etc/udev/rules.d
There were more, but basically folders the tutorial said you had to make
81 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 12/10/2022 in #fix-my-printer
MCU shutdown when homing (BTT octopus F446)
Figured it out, was a misplaced Z driver, apparently it checks for comms on all drivers when homing any axis
4 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 12/10/2022 in #fix-my-printer
MCU shutdown when homing (BTT octopus F446)
Theres nothing wrong with the wiring. I have a printer configuration that can move the axes, but is missing configurations. When I restart with the ratrig V-Minion configuration, it shuts down when trying to home. The extruder is working though
4 replies
RRCRat Rig Community [Unofficial]
•Created by quickest-silver on 12/3/2022 in #ratos-support
RatOS + BigTreeTech CB1 Pi Clone
I cant get the errors now, but I did manage to get through the tutorial by deleting folders and files. I didnt see many errors
81 replies
RRCRat Rig Community [Unofficial]
•Created by decent-aqua on 12/3/2022 in #ratos-support
RatOS + BigTreeTech CB1 Pi Clone
Says in the tutorial OP posted
81 replies
RRCRat Rig Community [Unofficial]
•Created by cloudy-cyan on 12/3/2022 in #ratos-support
RatOS + BigTreeTech CB1 Pi Clone
/home/pi/ratos-configurator/scripts/setup.sh
81 replies
RRCRat Rig Community [Unofficial]
•Created by fair-rose on 12/3/2022 in #ratos-support
RatOS + BigTreeTech CB1 Pi Clone
I rebooted several times after doing a couple of steps, stopped working after running ratos-install.sh. I did run the setup.sh too though
81 replies
RRCRat Rig Community [Unofficial]
•Created by foreign-sapphire on 12/3/2022 in #ratos-support
RatOS + BigTreeTech CB1 Pi Clone
I got stuff working, but when I reboot the services do not start. Im guessing it's the ratos-install.sh thats messing it up. Just wanted to put it out there.
81 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 12/7/2022 in #ratos-support
Trying to access configure gives 502 bad gateway error
doesnt help, I tried
17 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 12/7/2022 in #ratos-support
Trying to access configure gives 502 bad gateway error
But is there a way to get it connected to wifi without the configurator? It seems to be working, though the Octopus board is crashing everytime I try to run the steppers, but it's likely a hardware issue
17 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 12/7/2022 in #ratos-support
Trying to access configure gives 502 bad gateway error
Exactly, I am connected to the hotspot, I want to move it over to my wifi
17 replies