CoffeeSquirel
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 7/19/2024 in #ratos-support
Does RatOS RC1 flashing delete bootloader?
Hi, I tried the 2.1 RC1 a little while ago with a Pi and my Octopus V1.1 board, whih worked fine. But now Im trying to get it to work with a normal Mainsail installation, and theres no way it shows up. Tried flashing the firmware with an sd card, but no luck.
So my question is, do the RatOS flashing remove the bootloader so I have to flash a new bootloader onto the board?
7 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 9/28/2023 in #ratos-support
Exclude object not appearing in mainsail/RatOS
Hello, after much frustration I have decided to ask here.
I have added [file_manager] object processing to the bottom of my Moonraker.conf, and the [exclude_object] to printer.cfg just above the save config section, slicer has enabled labeling, yet still no option for excluding object.
I dont understand why it doesnt appear, I also have uploaded new files to the printer, but nothing changes. Any suggestions? I am running on a BTT CB1 though.
1 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 4/5/2023 in #fix-my-printer
Printer fails to probe a bed mesh when starting a print
Hey, I have a problem with my V-Minion, whenever it goes to do a bed mesh, it manages to probe some points, but suddenly plunges the nozzle into the bed (thank you for that spider coupling). The Mainsail console spits out this:
10:11 AM
G91
G1 Z+25 F1500
10:11 AM
G91
G1 Z+25 F1500
10:11 AM
Extrude below minimum temp
10:11 AM
Extrude below minimum temp
See the 'min_extrude_temp' config option for details
10:11 AM
Extrude below minimum temp
10:11 AM
Extrude below minimum temp
See the 'min_extrude_temp' config option for details
10:11 AM
Extrude below minimum temp
10:11 AM
Extrude below minimum temp
See the 'min_extrude_temp' config option for details
10:11 AM
Extrude below minimum temp
10:11 AM
Extrude below minimum temp
See the 'min_extrude_temp' config option for details
10:11 AM
echo: Cleaning up...
10:11 AM
No trigger on probe after full movement
10:11 AM
No trigger on probe after full movement
10:11 AM
No trigger on probe after full movement
Any ideas what may cause this? The sample retract distance is 3mm
11 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 12/10/2022 in #fix-my-printer
MCU shutdown when homing (BTT octopus F446)
So I try to home my X-axis, but the MCU shuts down and I have to do a firmware restart. It did work on a previous install (RatOS on a CB1, screws up on a reboot), so Im trying to configure a standard klipper install (with klipperscreen). I did git-pull the ratrig configurations, and configured for the V-Minion, rooted out the errors I was getting. I uncommented two lines:
#[include config/printers/v-minion/input-shaper-single.cfg]
#[include config/shell-macros.cfg]
This is the logfile from klippy:
https://docs.google.com/document/d/15IKMOQANIN7KDFTT5oDK_xRIUf-vsLpPuEeErS3N7gg/edit?usp=sharing
I tried un-inverting the enable_pin, its making noise, so I inverted it again. Everything else on the system seems to be working, any suggestions on what might be the issue?
4 replies
RRCRat Rig Community [Unofficial]
•Created by CoffeeSquirel on 12/7/2022 in #ratos-support
Trying to access configure gives 502 bad gateway error
Hey, I am trying to install RatOS on a Raspberry Pi Zero W, but I want to connect it to my wifi. As I understand you do that in /configure, but it gives me that error.
Is there any way to fix the error or connect the RPi without /configure?
17 replies