🌊 Jamiroquai 🌊
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 10/2/2024 in #fix-my-resonance
V-Core 3.1 500 Unenclosed
6 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 10/2/2024 in #fix-my-resonance
V-Core 3.1 500 Unenclosed
I tightened both belts, I can't see anything binding
6 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 10/2/2024 in #fix-my-resonance
V-Core 3.1 500 Unenclosed
6 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 10/2/2024 in #fix-my-resonance
V-Core 3.1 500 Unenclosed
Thank you for your response, I appreciate it. I will tighten the belts tonight and will post the results 🙂
6 replies
RRCRat Rig Community [Unofficial]
•Created by resmon on 4/8/2024 in #fix-my-print
Under extrusion problems at solid infill
You probably already solved it by now. I had a similar issue to this recently after building my V-Core 500, I use the Rapido v2 UHF however. Also using the same extruder as you. I would definitely go with what you suggested with checking the max volumetric speed. You can do the volumetric test using orcaslicer to see how it performs overall. From there you can measure where the print starts to fail and you can calculate the correct max volumetric speed: https://www.obico.io/blog/maximum-volumetric-speed-test-in-orcaslicer-a-comprehensive-guide/
3 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/6/2024 in #fix-my-mesh
V-Core 3.1 500 Extreme Cornering in Bed Mesh
Thank you, will check it out
214 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/6/2024 in #fix-my-mesh
V-Core 3.1 500 Extreme Cornering in Bed Mesh
Using BL Touch
214 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/6/2024 in #fix-my-mesh
V-Core 3.1 500 Extreme Cornering in Bed Mesh
@VisualTech48 I calibrated the z-offset but when I go to print it seems to set to zero and drag against the build plate
214 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
I've changed the post tagged to Solved for the time being, everything seems to run fine
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
This could be the case
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/6/2024 in #fix-my-mesh
V-Core 3.1 500 Extreme Cornering in Bed Mesh
Okay managed to fix that problem haha
214 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
Heater, bed, steppers, extruder all working at the same time
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
Everything is working, even loading filament on the extruder works this time
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
I had a 10A IEC with a rocker switch on hand
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
The 15A IEC melted a tiny bit as well. So I was lucky that didn't develop into a fire
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
Haha alrighty let's get to work
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
Darn
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
Surely the extruder motor doesn't take that much juice?
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
Everything else has been running fine during the bed mesh calibration. When I went to load filament using the option on Klipper that is when it all went to hell
36 replies
RRCRat Rig Community [Unofficial]
•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer
RatRig V-Core 500 'Blew Up'
Yeah the IEC320 C14 with fuse 15A
36 replies