insonifi
RRCRat Rig Community [Unofficial]
•Created by ChrisTopZ on 1/6/2024 in #fix-my-printer
Mysterious "Lost communication with MCU 'mcu'" error began occuring out of the blue
I had such an issue when I added a separate PSU for RPi. My EBB36 would regularly loose connection. I fixed it by connecting all ground terminals between PSUs and wiring a ground to the USB cable (which I did not have before).
5 replies
RRCRat Rig Community [Unofficial]
•Created by insonifi on 5/27/2023 in #fix-my-printer
Toolboard looses communication when generating a shaper graph for Y axis
it is 5.09V.
I connected another USB cable to the EBB. Which has all 4 pins connected and generation completed successfully.
Since I made my own lightweight USB cable that only had 2 data lines connected, I plan to connect the ground line too. Just to be sure.
3 replies
RRCRat Rig Community [Unofficial]
•Created by insonifi on 5/22/2023 in #fix-my-printer
Inductive probe suddenly triggers at a mere ~2mm
hm.. I will check. Although, with current mount I am not able to ensure it. I guess I will try to print a longer mount as soon as I can. And then progress towards EVA3
21 replies
RRCRat Rig Community [Unofficial]
•Created by insonifi on 5/22/2023 in #fix-my-printer
Inductive probe suddenly triggers at a mere ~2mm
is there anything I can do to ensure my new heatbreak is not destroyed again?
21 replies
RRCRat Rig Community [Unofficial]
•Created by insonifi on 5/22/2023 in #fix-my-printer
Inductive probe suddenly triggers at a mere ~2mm
yeah, I am planning it when I will be able to print it :))
21 replies
RRCRat Rig Community [Unofficial]
•Created by insonifi on 5/22/2023 in #fix-my-printer
Inductive probe suddenly triggers at a mere ~2mm
https://2.eva-3d.page/addons/probes/inductive/
there is only one option for each probe size
21 replies
RRCRat Rig Community [Unofficial]
•Created by insonifi on 5/22/2023 in #fix-my-printer
Inductive probe suddenly triggers at a mere ~2mm
perhaps, I exaggerated a bit. that is how it was until the accident
21 replies
RRCRat Rig Community [Unofficial]
•Created by insonifi on 5/22/2023 in #fix-my-printer
Inductive probe suddenly triggers at a mere ~2mm
21 replies
RRCRat Rig Community [Unofficial]
•Created by insonifi on 5/22/2023 in #fix-my-printer
Inductive probe suddenly triggers at a mere ~2mm
as far as I remember, it was impossible to have it closer to the bed with a Volcano on EVA2. I already pushed the probe as far down while still being held.
21 replies
RRCRat Rig Community [Unofficial]
•Created by evident-indigo on 5/18/2023 in #fix-my-resonance
How bad/normal/good is this?
beware, I am a weak authority, my printer is still in a pretty bad shape 😁
10 replies
RRCRat Rig Community [Unofficial]
•Created by like-gold on 5/18/2023 in #fix-my-resonance
How bad/normal/good is this?
looks, perfect to me.
10 replies
RRCRat Rig Community [Unofficial]
•Created by rival-black on 5/18/2023 in #fix-my-resonance
How bad/normal/good is this?
looks a bit loose then. I have 400 and my X resonance is around 72Hz.
well, I don't see any spikes on your X/Y. Cannot say what it might be on your belt tension graph, not sure how important it is if axes are fine.
10 replies
RRCRat Rig Community [Unofficial]
•Created by xenial-black on 5/18/2023 in #fix-my-resonance
How bad/normal/good is this?
As far as I understand the issue, it looks pretty good.
What is the size and frequency you tuned the belts to?
10 replies
RRCRat Rig Community [Unofficial]
•Created by provincial-silver on 4/25/2023 in #fix-my-print
bump on outer perimeter in a specific part of the model
maybe, you can change slicer parameters for just these layers
17 replies
RRCRat Rig Community [Unofficial]
•Created by eastern-cyan on 4/25/2023 in #fix-my-print
bump on outer perimeter in a specific part of the model
17 replies
RRCRat Rig Community [Unofficial]
•Created by genetic-orange on 4/25/2023 in #fix-my-print
bump on outer perimeter in a specific part of the model
it is that spot 🙂
17 replies
RRCRat Rig Community [Unofficial]
•Created by like-gold on 4/25/2023 in #fix-my-print
bump on outer perimeter in a specific part of the model
17 replies
RRCRat Rig Community [Unofficial]
•Created by correct-apricot on 4/25/2023 in #fix-my-print
bump on outer perimeter in a specific part of the model
17 replies
RRCRat Rig Community [Unofficial]
•Created by typical-coral on 4/25/2023 in #fix-my-print
bump on outer perimeter in a specific part of the model
17 replies
RRCRat Rig Community [Unofficial]
•Created by Plynix on 4/22/2023 in #fix-my-printer
Tightening the lower belt makes the moving the x axis a lot harder
overtightened idlers?
14 replies