Grimstod
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
I ordered two new probes.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
When i do an X Y Z homing it works fine but when i click z-tilt that is when the error appears.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
Thus thing is a huge paperweight until i can figure this out.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
When i loft the bed up to trigger it the light does go out. Nothing happens on the Console though
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 6/4/2023 in #fix-my-print
printing round tubes
That perimeter order change has worked Still a tinny few blobs but not many. Much i@proved.
12 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 6/4/2023 in #fix-my-print
printing round tubes
I did a wider 0.55 inner layer width over the default .45 and that actually helped a little just not enough.
12 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 6/4/2023 in #fix-my-print
printing round tubes
My layer height was 0.2 and i have also tried 0.15. Nozzle is a 0.4
12 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 6/4/2023 in #fix-my-print
printing round tubes
So right this minute i am trying out a different layer order. It was set to do outer and inner walls first then infill. I reversed that.
12 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 6/4/2023 in #fix-my-print
printing round tubes
For external perimeters i had it at 35mms and internal is 200
12 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 6/4/2023 in #fix-my-print
printing round tubes
Ill give that a try.
12 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/15/2023 in #fix-my-resonance
Before and after impute shaper shows no change
12 replies
RRCRat Rig Community [Unofficial]
•Created by schlumpfi5649 on 3/10/2023 in #fix-my-printer
Input shaper not work
Have you checked for any loose bolts. I know it sounds silly but when I went back and re-check my machine after a few months, I found a few loose.
7 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/7/2023 in #fix-my-printer
Octopus 1.1 firworks
23 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/7/2023 in #fix-my-printer
Octopus 1.1 firworks
23 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/7/2023 in #fix-my-printer
Octopus 1.1 firworks
Here are some close up images. I removed the one jumper and plugged it back in. No smoke or flames this time.
23 replies