hikerjim
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/7/2025 in #fix-my-printer
Ratos 2.x
I'm on RatOS 2.1. I haven't changed anything in my slicer. And that is the only printer that I use super slicer on. I have another printer but I use Cura for that one. I didn't know there was a post processor section of the slicer. Once I had it up and working I left it.
5 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 6/6/2023 in #fix-my-printer
belt shifting
Thank you...lots to think on there. I've been printing with this since late last summer and especially the last month or 2 its been running real good. I put the new Rapido Plus hotend on it and its the smoothest and fastest its ran. Guess time to take the corner apart
Thank you again for the info
12 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/9/2023 in #fix-my-printer
z tilt issue
ok, here is good log
10 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/9/2023 in #fix-my-printer
z tilt issue
no, let me re-do it and I'll upload a better one
10 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/9/2023 in #fix-my-printer
z tilt issue
Sorry about that here is the log file. I ran the stepper_buzz when I first built it but not since, ill run those again
10 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/9/2023 in #fix-my-printer
z tilt issue
Ok, here is video.. right around 19 second mark is the first instance of it happening.
10 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/9/2023 in #fix-my-printer
z tilt issue
There is printer.cfg, I'll work on the video next
10 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/8/2023 in #fix-my-printer
x endstop cable
Yep, you are both correct, somehow I totally missed that. Thank you
5 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/6/2023 in #fix-my-printer
Rapido plus hotend
have you printed using that yet? If so what has your impression been so far?
12 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/6/2023 in #fix-my-printer
Rapido plus hotend
oh... cool, thank you!!
12 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 4/6/2023 in #fix-my-printer
Rapido plus hotend
this might have done it. So what does that mean/do? It's reading correctly now. After dinner I'll try to change temp and see if that works, but i'm curious as to what that does.
12 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 3/14/2023 in #fix-my-printer
printhead gone wrong
As it turns out it was back left motor that was the issue, or at least 1 of the issues. I think there were 2 issues, but second one not sure of unless it was the board.
12 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 3/14/2023 in #fix-my-printer
printhead gone wrong
I've gone through and checked and tightened all nuts and bolts on all pullies, I've tightened the nuts that the print head slides on. Nothing has changed.... except I'm about to make this a very expensive boat anchor
12 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 3/14/2023 in #fix-my-printer
printhead gone wrong
So far I've replaced both the X and Y driver's, I've replaced the board with a brand new board out of the box and I've tightened the belts and loosened the belts. If move the bar by hand the print head does not move which is good. I'll check all the pullies...I'm running out of ideas
12 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 1/17/2023 in #fix-my-printer
failed to init Unable to read tmc uart
I just found a wiring difference between the Pro 446 and V1.1 going to shutdown and fix that
7 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 1/17/2023 in #fix-my-printer
failed to init Unable to read tmc uart
what is the best way to confirm that? I'm not an electrical expert by any means.
7 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 1/17/2023 in #fix-my-printer
failed to init Unable to read tmc uart
7 replies
RRCRat Rig Community [Unofficial]
•Created by hikerjim on 1/10/2023 in #fix-my-printer
z probe issues
Yea, when I hooked up the brand new backup z probe I didn't attach it i just hooked it up and got the same exact results.
5 replies