3DBIM-Solutions
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/5/2025 in #ratos-support
RatOS 2.1 RC3 issue with configurator and T1.
Did you solve it?
10 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/5/2025 in #ratos-support
RatOS 2.1 RC3 issue with configurator and T1.
But be careful this is for the ebb42 v1.2 toolboard
10 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/5/2025 in #ratos-support
RatOS 2.1 RC3 issue with configurator and T1.
10 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/5/2025 in #ratos-support
RatOS 2.1 RC3 issue with configurator and T1.
What toolboard do you use? I think you probably have not placed the jumper correctly placed. That causes temp differences. If you use a ebb42 v1.2 and dont have pt1000 then place the jumper horizontal and otherwise vertical where pt1000 is
10 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
Thanks for pointing me in the direction again for the probeoffset and taking your time to help people!
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
For the future I ordered a Beacon RevH low profile for my vcore 3.1 when i find the best duct for my eva3 toolhead
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
My 2mm offset became around 3mm this way and cause the triggering to be unreliable
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
I have found the issue! Its a combination of probe inaccuracy and offset from the nozzle was at the edge of beeing triggered or not. I probably have caused this when cleaning the nozzle,
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
In a few hours I can. Thnx for thinking with me
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
Printer.cfg?
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
Yes its triggered when i do that
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
I always test by putting a Spacer in between and then check the endstop
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
2mm max
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
Ok glad then that I havent done it yet haha. I always test my machines for stepper directions by setting all axis in the centers and then home everything axis by axis. So stepper direction isnt the problem
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
No have not used it. Cant remember I ever used that command. What also is strange is that before the tuning I have succesful homed xyz multiple times, even did a z tilt and bed mesh calibrate without problems.
But i will try the set kinematic center in a few hours!
23 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 1/2/2025 in #fix-my-printer
When homing z the probe doesnt trigger and rams the hotend in the bed
Optical, when I hold something iron to the probe the red light on the top will light up and 10 out of 10 times tried the same result.
In the machine Tab below where the endstops are open or triggered.
I have a npn no probe so when activated is should say triggered and it does when holding something iron to it.
And of course I have leveled the bed manual so the nozzle is slight above the bed with a feeler plate between them. And after that I checked the endstops if it says triggered or not and optical also
23 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/27/2024 in #fix-my-printer
Frequent Issue - MCU 'mcu' shutdown: Timer too close
Another thing could be to much resources used on the pi but with what you have listed i dont think thats the issue
15 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/27/2024 in #fix-my-printer
Frequent Issue - MCU 'mcu' shutdown: Timer too close
I had this issue too. Problem is probably the SD card. Changed my card today and after that everything was ok again
15 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/26/2024 in #ratos-support
ratos 2.1-rc2 issues (no initial config)
I had the invalid packages also but what I found out was that when waiting a bit longer then the browser refreshed and all where able to update. After that I had 116 system packages not wanting to install but after a few tries they did and everything worked. So it looked like extraordinary 😂 paitience was key in my case.
I also had the bed_mesh error and the resonance error, but that was fixed after updating everything and set the adxl for x and y..
94 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBIM-Solutions on 12/30/2024 in #ratos-support
Existing command TEST_RESONANCES not found in RatOS override
That was the solution for all the problems. The toolboard was recognised again and klipper has no errors for this topic. Some other minor issues to be solved but if needed ill open another post. Thanks for your help!
11 replies