XHeli
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
i have similar experiences, i dont have a chance to get the left t0-x to more then 500.000, where the t1-x head was something like a poc to get that to over 3.000.000 and with a curve that cant be better, id did hundereds of tension adjustments from flattering low to iron rod like tension and on no point a nearly satisfying curve. the x-mgn rail is a little bit bended in direction of z before installation (maybe this is a reason?) I use linearrail lubricant aswell, that is thicker then oil, but i used that on t1 too. Im clueless. Also also checked als pulleys rebuild the beltholders on toolhead, adjust all perfectly square. All supersmooth, no rattling, just silent
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
Its a 400 machine
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
I tested all beetween so looose, that the belt is wobbeling and so tight that the belt is like an iron rod, no point in the way of the two point leads to more then 80.000 (i did approx 40 Steps from loose to tight). On T1 all no problem, just a T0 issue (on X and Y axis the same missbehavior)
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
maybe tool-board damaged ?
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
hand-movement feels very smooth
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
all idler pulleys controlled, belt always in the middle of pulleys
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
right and left x-tension is almost the same and gantry perfectly aligned
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
The right side is a poc to adjust for x and y axis
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
hello again and good morning (if the timezone fits;). I have a issue, and im a little bit confused: Wether i measure X or Y Axsis, every time the PSD is far lower on the left side (100 Times lower, i.e. 60.000 instead of 2.000.000) i tried every tension from extremly low to like an iron rod. In the best case i reached 80.000.
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
thanks, i try it
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
I tried a couple of thightness levels from very low to thight and literly nothing changed :/ But i can try again a far less tighness
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
i never saw such flat blue line O_O
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
1158 replies