NT8B - Leon
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
Perfect! thank you.
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
Again, your help is awesome and greatly appreciated!
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
Thanks! Just to confirm, are these changes made in the printer.cfg file?
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
On your question about modifications, it's possible that this printer actually may not have the stock stepper motors installed. I'm not able to access the printer until Tuesday this week to verify, but looking at records I can find online, it appears that this printer has stepper motor specifications as follows:
NEMA 17. 0.9° Step Angle. 400 Steps Per Revolution. 2.8V Rated Voltage. 1.68A Phase. 4.4kg/cm (61oz/in) Holding Torque. 48mm Body. 5mm Output Shaft. Looking at the values given above, I'm wondering if the upgraded OS is expecting steppers with a step angle of 1.8 degrees? Otherwise, there are no other modifications to the motion hardware in this printer. If this is the likely problem is it possible to adjust for this in the configuration wizard?
NEMA 17. 0.9° Step Angle. 400 Steps Per Revolution. 2.8V Rated Voltage. 1.68A Phase. 4.4kg/cm (61oz/in) Holding Torque. 48mm Body. 5mm Output Shaft. Looking at the values given above, I'm wondering if the upgraded OS is expecting steppers with a step angle of 1.8 degrees? Otherwise, there are no other modifications to the motion hardware in this printer. If this is the likely problem is it possible to adjust for this in the configuration wizard?
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
OK, just got done with the reinstall process, and all looks good. Thank you again! I'm now back to the original problem, namely that the x- and y-axes movements are limited to the left rear quadrant of the build plate. Picking up where we left off, I'm attaching the debug.zip file.
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
Thank you Mikl! There's no need to apologize. I think you and the rest of the team are doing wonderful work. I'll do another install and will report back on how it goes.
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
Thanks for getting back to me. Unfortunately, I decided to try a clean re-installation of the OS under the assumption that it might clear up my issue. It turns out that seem to have dug myself into a deeper hole. The issue I have now is that when I run through the v2.1 configuration process I cannot get past the firmware installation step. I keep receiving version mismatch errors. I've tried three firmware update methods available in the configurator. I first tried using the autoflash method. When the autoflash process completed, I received the following message:
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
Ok. I wondered about rotation distance as well but I’m not sure how to tackle it. I’ll rerun the configurator and if that doesn’t work maybe I will try another clean installation. I successfully upgraded a vCore200 last week and it works fine. Thanks for your comments. It’s greatly appreciated.
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
Yes, the printer will home all axes, and z-tilt as well. Probing for the z-tilt covers only the back-left quarter of the build area.
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 10/19/2024 in #ratos-support
x- and y-axis positioning incorrect after upgrading to RatOS v2.1-RC1
Thanks!
29 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 6/14/2023 in #ratos-support
Extruder not working
That was the problem. Thanks for the help. Greatly appreciated!
7 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 6/14/2023 in #ratos-support
Extruder not working
I set the hot end to print temp (>150) for this testing.
7 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 6/14/2023 in #ratos-support
Extruder not working
I haven't yet created any gcode files in the slicer for this printer. The issue I have occurs when I send extrude or retract commands from the mainsail console.
7 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 5/27/2023 in #ratos-support
No trigger on z after full movement
OK - I'm not sure what happened but I'm now getting movement as expected on the z-axis when I home z. I went through a process of checking and re-seating the motor connectors so maybe that was part of the problem? I don't know... Anyway, it looks like I can proceed with adjusting the height of the sensor and the rest of the setup process. I'm very grateful for your help. Thank you for being there.
7 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 5/27/2023 in #ratos-support
No trigger on z after full movement
checking for noise next.\
7 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 5/27/2023 in #ratos-support
No trigger on z after full movement
Stand by and I'll double check. I can confirm that the coupler/leadscrew is properly tightened.
7 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 5/25/2023 in #ratos-support
Klipper reports: ERROR Duplicate Chip name 'probe'
I appreciate the fast help.
26 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 5/25/2023 in #ratos-support
Klipper reports: ERROR Duplicate Chip name 'probe'
OK - Thank you! that appears to have solved the problem.
26 replies
RRCRat Rig Community [Unofficial]
•Created by NT8B - Leon on 5/25/2023 in #ratos-support
Klipper reports: ERROR Duplicate Chip name 'probe'
Apologies. pronter.cfg now attached.
26 replies