technofrikus Comments - Answer Overflow

technofrikus

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

Confirmed working, now! Let the same gcode run dry over night and no problems. Thanks a lot! :pray:

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

If skew being the reason, I think this would explain why it did not trigger with just a small cutout of the big file? Maybe, not sure how this is calculated.

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

Skew! Ohhh. I also thought about filament shrinkage, which I also "use" to get an accurate size. With this enabled the model is not 405,00 mm but 405,89mm in length during printing. But then there is still ~1mm left on each side (408mm total length available). But with the skew enabled it is not enough maybe? Thanks! Will try that!

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

…or not. Was not able to reproduce it with a cutout of the same exact model at the same position :shrug: Worked fine

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

It seems to be a slicer issue, not Klipper, at least this sounds exactly like my problem: https://github.com/SoftFever/OrcaSlicer/issues/3107

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

from the top

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

My best guess is that these z-hop movements caused it, but why the top one and not the other two (exact layer were it failed shown)? they worked fine for some reason although this is a straight 90° wall, not tilted.

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

I printed one successfully but now the second one (with slightly different gcode) failed at 96 Percent :dunkelheit: Move out of range: -0.019 263.662 23.287 [140557.543]

19 replies

RRCRat Rig Community [Unofficial]

•Created by technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

my printer.cfg

19 replies

RRCRat Rig Community [Unofficial]

•Created by Mr. Hye on 4/28/2024 in #fix-my-print

Rough artifacts on surface

Maybe a partially clogged nozzle?

61 replies

RRCRat Rig Community [Unofficial]

•Created by swdee on 12/28/2023 in #fix-my-resonance

Trying to tune Vcore 400mm

I dont have much experience with this either, but what I read is, when the graphs look very different from the goal, usually something mechanical is not correct. Loose screw etc. And did you watch this video from the pins? Explains a lot. https://youtu.be/M-yc_XM8sP4

46 replies

RRCRat Rig Community [Unofficial]

•Created by fair-rose on 7/5/2023 in #german-support

V-Core 3.1 unsaubere X- und Y-Achsen Bewegung

Habe ich auch gerade 🥳

19 replies

RRCRat Rig Community [Unofficial]

•Created by like-gold on 7/5/2023 in #german-support

V-Core 3.1 unsaubere X- und Y-Achsen Bewegung

Die von RatRig sind das

19 replies

RRCRat Rig Community [Unofficial]