Technofrikus Posts - Answer Overflow

Technofrikus

•Created by Technofrikus on 5/17/2024 in #ratos-support

Move Out of range but not

The problem: After the print fails because of "Move out of range" I can still move the printhead manually (stilled homed). The position is at 1.77mm in X (where it failed) but if I tell it to move 0.1mm to the left (just did this in the picture) it says again out of range. But it clearly is not. Accoriding to the error message + 0,1mm the real current position is 0,046mm and not 1,77mm. There seems to be an offset but I dont know from where? Background: I want to print a keyboard filling nearly the complete x length of my vCore 3.1 400mm. It is 405mm long, but I increased the x length in the firmware and Orca Slicer to 408mm. I doublechecked and there is enough clearance to move the head this far. I printed several keyboards before with this setup a few months ago. But now it doesnt work anymore. Orca Slicer does not give a warning of a move outside the printbed. I did some more tests and got it to work like this: increase X in the Slicer to 410mm but keep it at 408mm in the printer.cfg (otherwise the fan duct collides). But thats not a good solution. Also tried to disable exclude and name object since Helge said it might have bugs, but did not solve the problem. Also updated to the latest everything and did not solve it. (the print in the picture is just a small part of the complete print at the same position, for testing)

19 replies

RRCRat Rig Community [Unofficial]

•Created by Technofrikus on 5/4/2024 in #fix-my-print

underextrusion-like artifacts at small layer heights

3 replies

RRCRat Rig Community [Unofficial]

•Created by Technofrikus on 5/14/2023 in #ratos-support

4028 fan on sht36 v1 toolboard not controllable

17 replies

RRCRat Rig Community [Unofficial]

•Created by Technofrikus on 5/12/2023 in #ratos-support

Flashing of SHT36 Toolboard does not finish

When using the Wizard in RatOS 2.0.1 for flashing the SHT36 v1, the flashing starts, but the flash button gets green again and I cant press next. Using an Octopus Board and a Raspberry Pi 3B, connected the SHT36 via USB, DFU jumper is on, CAN termination jumpers are on (not related, but wanted to mention it), CAN is not connected. This is the error:

[17:44:34.876] ^[[31mERROR^[[39m (1155): ^[[36mFailed to flash device.^[[39m
    err: {
      "type": "TRPCError",
      "message": "Failed to flash device.",
      "stack":
          TRPCError: Failed to flash device.
              at Procedure.resolve [as resolver] (/home/pi/ratos-configurator/build/server/chunks/932.js:566:13)
              at runMicrotasks (<anonymous>)
              at processTicksAndRejections (node:internal/process/task_queues:96:5)
              at async Array.<anonymous> (/home/pi/ratos-configurator/node_modules/.pnpm/@trpc+server@9.27.3/node_modules/@trpc/server/dist/router-aaecbe82.cjs.prod.js:101:25)
              at async callRecursive (/home/pi/ratos-configurator/node_modules/.pnpm/@trpc+server@9.27.3/node_modules/@trpc/server/dist/router-aaecbe82.cjs.prod.js:119:24)
              at async next (/home/pi/ratos-configurator/node_modules/.pnpm/@trpc+server@9.27.3/node_modules/@trpc/server/dist/router-aaecbe82.cjs.prod.js:126:20)
              at async callRecursive (/home/pi/ratos-configurator/node_modules/.pnpm/@trpc+server@9.27.3/node_modules/@trpc/server/dist/router-aaecbe82.cjs.prod.js:119:24)
              at async Procedure.call (/home/pi/ratos-configurator/node_modules/.pnpm/@trpc+server@9.27.3/node_modules/@trpc/server/dist/router-aaecbe82.cjs.prod.js:144:20)
              at async /home/pi/ratos-configurator/build/server/chunks/669.js:473:24
              at async Promise.all (index 0)
      "originalError": "An error occured while attempting to run script",
      "code": "INTERNAL_SERVER_ERROR",
      "name": "TRPCError"
    }

43 replies

RRCRat Rig Community [Unofficial]

•Created by Technofrikus on 5/12/2023 in #ratos-support

Wifi special characters

3 replies

RRCRat Rig Community [Unofficial]

•Created by Technofrikus on 3/1/2023 in #ratos-support

Gcode file list doesnt load anymore ... too long

I recently changed the amount of gcode files displayed to "all" because I wanted to delete nearly all of them, because just loading the list in Klipper Screen takes a long time. Then I got distracted and didnt delete anything. When I now visit the file list on RatOS in the Browser (not KlipperScreen) it never finishes to load, the site crashes and I have to reload the startpage. So I can basically not access my files anymore from the Browser. And I cant change the setting back, because the dropdown list is on the bottom. At least I cant see it.

5 replies

Gaming

Programming