guesswhatsthisparlor
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
MCU Protocol Error
I don't know, I just know it wasn't blinking red
17 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
MCU Protocol Error
Hey. The problem was that my beacon wasn't on, so it didn't recieve any updates and some files were corrupted
17 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
Thank you
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
A reinstall was all it needed
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
All is done
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
It seems I had a couple of corrupt files and noticed that my beacon cable is trash
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
It's ending about now
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
Ok
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
How do I fix it? I'm sure that I didn't change the password, I would remember it
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
only ssh [IP Adress]
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
Password is not raspberry
Also [email protected] doesn't work
15 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
MCU Protocol Error
17 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
MCU Protocol Error
17 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/24/2024 in #fix-my-printer
MCU Protocol Error
MCU Protocol error
This is frequently caused by running an older version of the
firmware on the MCU(s). Fix by recompiling and flashing the
firmware.
Your Klipper version is: v0.12.0-261-g248d3dbf-dirty
MCU(s) which should be updated:
mcu: Current version v0.12.0-261-g248d3dbf
rpi: Current version ?-20240528_040405-fv-az891-544
toolboard_t0: Current version v0.12.0-261-g248d3dbf
beacon: Current version Beacon 1.1.0
Up-to-date MCU(s):
<none>
Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Outdated Beacon firmware version 0.1.0, current version is 2.1.0.
Please run
install.sh or update_firmware.py update all to update to the latest version.
Using an outdated firmware version can result in instability or failures.
mcu 'beacon': Unknown command: beacon_contact_home17 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/19/2024 in #fix-my-printer
Octopus Pro V1.1
The best
26 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/19/2024 in #fix-my-printer
Octopus Pro V1.1
THANK YOUUUUUU
26 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/19/2024 in #fix-my-printer
Octopus Pro V1.1
YEEEEEEEESSSSSSSSSSSSSSS
26 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/19/2024 in #fix-my-printer
Octopus Pro V1.1
HFEKFHKW
26 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/19/2024 in #fix-my-printer
Octopus Pro V1.1
WORKEDFDDDE
26 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 7/19/2024 in #fix-my-printer
Octopus Pro V1.1
WORED
26 replies