Yannic
Yannic
RRCRat Rig Community [Unofficial]
Created by Yannic on 6/8/2024 in #ratos-support
Moonraker Update fails
Thank you for your help. I decided to install the new version 2.1 with a new image. I no longer have any problems. Feedback on the current status of 2.1: The setup wizard is incredibly useful. Compared to the previous versions of RatOS, I was ready to use the printer much faster. The selection of individual components is very handy and simplifies the process a lot. Many thanks for the development of version 2.1
22 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 6/8/2024 in #ratos-support
Moonraker Update fails
pi@ratos:~/moonraker $ git fetch origin
error: cannot lock ref 'refs/remotes/origin/master': unable to resolve reference 'refs/remotes/origin/master': reference broken
From https://github.com/Arksine/moonraker
! [new branch] master -> origin/master (unable to update local ref)
pi@ratos:~/moonraker $
pi@ratos:~/moonraker $ git fetch origin
error: cannot lock ref 'refs/remotes/origin/master': unable to resolve reference 'refs/remotes/origin/master': reference broken
From https://github.com/Arksine/moonraker
! [new branch] master -> origin/master (unable to update local ref)
pi@ratos:~/moonraker $
22 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 6/8/2024 in #ratos-support
Moonraker Update fails
Thats the output im getting
22 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 6/8/2024 in #ratos-support
Moonraker Update fails
pi@ratos:~ $ cd moonraker
pi@ratos:~/moonraker $ git reset --hard origin/master
warning: ignoring broken ref refs/remotes/origin/master
warning: ignoring broken ref refs/remotes/origin/master
fatal: ambiguous argument 'origin/master': unknown revision or path not in the working tree.
Use '--' to separate paths from revisions, like this:
'git <command> [<revision>...] -- [<file>...]'
pi@ratos:~/moonraker $
pi@ratos:~ $ cd moonraker
pi@ratos:~/moonraker $ git reset --hard origin/master
warning: ignoring broken ref refs/remotes/origin/master
warning: ignoring broken ref refs/remotes/origin/master
fatal: ambiguous argument 'origin/master': unknown revision or path not in the working tree.
Use '--' to separate paths from revisions, like this:
'git <command> [<revision>...] -- [<file>...]'
pi@ratos:~/moonraker $
22 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 6/8/2024 in #ratos-support
Moonraker Update fails
This was the answer I got after trying ti ssh into the printer.
pi@ratos:~ $ cd moonraker
pi@ratos:~/moonraker $ git status
On branch master
Untracked files:
(use "git add <file>..." to include in what will be committed)
moonraker/components/timelapse.py

nothing added to commit but untracked files present (use "git add" to track)
pi@ratos:~/moonraker $
pi@ratos:~ $ cd moonraker
pi@ratos:~/moonraker $ git status
On branch master
Untracked files:
(use "git add <file>..." to include in what will be committed)
moonraker/components/timelapse.py

nothing added to commit but untracked files present (use "git add" to track)
pi@ratos:~/moonraker $
22 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 6/8/2024 in #ratos-support
Moonraker Update fails
Thats the file after I try to do a soft recovery.
22 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 6/8/2024 in #ratos-support
Moonraker Update fails
To be honest, I am overwhelmed with this large file. It would therefore be very kind if someone with much more knowledge than me could take a look at the file.
22 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 6/8/2024 in #ratos-support
Moonraker Update fails
22 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/21/2023 in #fix-my-mesh
Z- TILT doesnt work correctly
Unfortunately, this does not solve the problem. Due to the fact that my lead screw decupler is jammed, it often happens that Z-Tilt is "out of range" and therefore aborts.
12 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/21/2023 in #fix-my-mesh
Z- TILT doesnt work correctly
I placed the bed on a very flat surface (granite worktop from the kitchen) and looked for deviations in the flatness of the bed using a flashlight and the light test. There was no light gap to be seen here. I therefore assume that my bed has no problem.
12 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/21/2023 in #fix-my-mesh
Z- TILT doesnt work correctly
I haven't gotten around to trying out all the options yet. My best guess is that the lead screw decupler is not working quite right. During assembly, I noticed that two of the three leadscrew decuplers are smooth. The third of the three leadscrew decuplers was binding (most likely due to a manufacturing or quality assurance error). I installed this difficult to move leadscrew decupler at the rear Z position. My guess is that the firmware is trying to level the bed but the movement is not getting there because the bed is not moving at these fine accuracies due to the binding lead screw decupler. I will try to remove the lead screw decupler and sand down the individual functional surfaces a little so that this lead screw decupler also moves smoothly. I will then report any news.
12 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/21/2023 in #fix-my-mesh
Z- TILT doesnt work correctly
I would like to utilize this bed as good as possible. It seems that an easy fix would be that the stepper near the back panel would go up a little bit to correct it.
12 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/17/2023 in #ratos-support
4028 fan speed control reversed
Thank you
17 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/17/2023 in #ratos-support
4028 fan speed control reversed
Okay. Who should I message to add a note to this guide?
17 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/17/2023 in #ratos-support
4028 fan speed control reversed
I followed the cabling instructions found here: https://ratrig.dozuki.com/Guide/12.+Wiring+Firmware+&+RatOS/143
17 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/17/2023 in #ratos-support
4028 fan speed control reversed
Yes
17 replies
RRCRat Rig Community [Unofficial]
Created by Yannic on 8/17/2023 in #ratos-support
4028 fan speed control reversed
Thank you very much. I'm glad it was my fault and not a hardware problem. I followed the wiring instructions and then the RatOS configuration. It didn't occur to me that I needed to add anything to my printer.cfg file. Maybe a note in the cabling instructions that you need to change something in the printer.cfg file would be helpful.
17 replies