Belly
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/18/2024 in #fix-my-print
Under Extrusion on corners
i would skip this test for now and do the flow test in orca. lets see what those look like.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
Couldn't take it. Stopped the print. Yup 0.6mm. Idiot.
Hey Thanks for that. Lol I just ordered a diamondback for it in 0.6mm so would have fixed it on accident tmrw. Excited to try it the right way now.
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
30 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/18/2024 in #fix-my-print
Under Extrusion on corners
did you change the nozzle to 0.6 in slicer? default is 0.4 i believe i guess unless you did pick 0.6 in setup wizard
6 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
orca*
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
tried orce 2.1 and 2.2 beta, also prusa 2.8
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
I'm curious if going to can would change anything
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
Yeah same thing here. It runs the max flow rate just fine but prints parts like garbage. I reduced max flow to 10 and it will print at that slow rate just fine.
I suspect some sort of extruder error. Like it can't keep up with quick lines of code but flow rate it can do cause it's not alot of code to process.
Either it way it pisses me off to have dropped now over 2500 on a machine that can't outrun my ender 3.
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
30 replies
RRCRat Rig Community [Unofficial]
•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print
And here we go again... first layer problem even with beacon3D
What happens if you dial back your flow multiplier just a tick like 0.01. my Theory is, from watching my own prints having the nozzle just a tad to close, the filament is just slightly over extruded so it looks good for the most part. and that little extra bit stacks tho as the next line and the next are layed down until it has nowere to go and starts to ripple.
72 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
This is the new new fan that arrived today. cfm is within is a few percent. Pressure wise its close. not the 4.5in but 3.0. Its the closest I can get to the supplied fan that isn't $84. It blows very hard compared to the amazon one I took off. https://www.digikey.com/en/products/detail/orion-fans/OD4028-24HBXE/16636974 I just cant run 12v now, that output died. I mean I guess I could drop a 12v supply in where the pi goes. Either way they are both damn loud. What are the thoughts about cpaping it?
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
Yeah I guess I'll do the steps, pa, all that jazz. Was hoping the included setting would be close enough.
Could it be a temp issue, like it's to cold to be printing this fast and another 10c would fix it? I've never been able to go above like 80mm before.
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
Brand new pla spool polymaker. Prints fine on my ender.
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 8/30/2024 in #fix-my-resonance
VC4 400Hybrid What am I looking at here?
56 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 8/30/2024 in #fix-my-resonance
VC4 400Hybrid What am I looking at here?
if its time
56 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 8/30/2024 in #fix-my-resonance
VC4 400Hybrid What am I looking at here?
im ready too
56 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 8/30/2024 in #fix-my-resonance
VC4 400Hybrid What am I looking at here?
some of it may be coming from the smart sensor? since it makes the motor tab thicker basically then the included standoff is to long and wont fit so I still need to trim that down and reinstall it. this would cause extra board mount floppieness I would think.
56 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 8/30/2024 in #fix-my-resonance
VC4 400Hybrid What am I looking at here?
56 replies