letniq
RRCRat Rig Community [Unofficial]
•Created by letniq on 1/21/2025 in #ratos-support
DC slammed on Homing after Set Kinetic Centre
I understand what the macro does however I believe when I hit home button it should home both heads correctly. Even in the macro is written to do G28 after your done. However G28 (Homing) is not working correctly
10 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 1/21/2025 in #ratos-support
DC slammed on Homing after Set Kinetic Centre
I don't think this is correct. After I hit the home button. T0 is moved at the normal homing speed and it stops at the end stops. T1 is slammed at very high speed nothing to do with the normal homing speed. In case T1 is at the end stop when you hit home you can clearly hear the belt skipping.
10 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 11/1/2024 in #ratos-support
IDEX Misses Z moves
Thanks. I will give it a try. I guess there will be future support in Orca as well
8 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
I can confirm that now It's working and I'm not getting control point error. The issue from the second video with the toolheads crashing was due to toolheads hitting my BTT runout sensors at the back and now the heads align in VAOC. Suddenly the move out of range error disappeared. After the new config I was getting the error and after sometime it disappeared.
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
I haven't tested but I checked the commits and they should solve the sanity check of control points. I haven't seen anything to solve the Move out of range error.
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
Thanks. I will update and try it tonight.
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
I only increased sanity check macro tolerance to allow me to set control point 327.xx as in the original it was not allowing to get below 328
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
everything is default as ratos image comes
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
mainsail
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
tonight I will be able to enable it and redo the tests
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
let me know in which in which file it is and I will check the value
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
I will troubleshoot again in the evening. The issue from the second video might be due to toolhead hitting my runout sensors at the back and skipping steps. But the first one I have no idea so far.
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
Even with Outter Diam set to 1 and 300 Px mm I still get the Error move out of range on Y as it's trying to set it to 478mm on 300 mm printer
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
Here is the video for the second issue. If I calibrate T0, calibrate T1 and go back to T0 it is misaligned. Align T0 again and go back T1 it will crach first to the right and then into T0 to the left.
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
the files was too big to upload here
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
I'm uploading the video now
118 replies
RRCRat Rig Community [Unofficial]
•Created by letniq on 10/27/2024 in #ratos-support
IDEX Offset Manual setup
First issue tried to calibrate and getting the following error once all is calibrated and I click Stop Calibration on 300mm printer
Move out of range: 114.463 478.061 30.800 [0.000]
118 replies