rmilyard
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 2/19/2025 in #fix-my-printer
Odd isssue now trying to run VAOC
So I upgraded my motor mounts and xy joint.
When I run VAOC now and move T0 in center then click T1 and do the same. When comes back to T0 it now heats up the hotend and sits here for awhile.
The recenter T0 and when click on T1 I get this error now: Shutdown due to Switched states detected in idex_mode.py. Please restart the host controller. Once the underlying issue is corrected, use the "FIRMWARE_RESTART" command to reset the firmware, reload the config, and restart the host software. Printer is shutdown
The recenter T0 and when click on T1 I get this error now: Shutdown due to Switched states detected in idex_mode.py. Please restart the host controller. Once the underlying issue is corrected, use the "FIRMWARE_RESTART" command to reset the firmware, reload the config, and restart the host software. Printer is shutdown
3 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/23/2025 in #fix-my-printer
Printing issues on new 500 IDEX
51 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/21/2025 in #fix-my-printer
IDEX 500 Orbiter V2 Smart Sensor issues.
40 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/8/2025 in #fix-my-printer
Issues with VAOC on new V-core 4 500 IDEX
I am working my way though this guide. https://docs.ratrig.com/v-core-4-0/idex-commissioning
I am at Initial vaoc calibration part of the guide. I line up T0 and T1. When I click the square to save I get this error:
6:13 PM Move out of range: 562.794 247.444 30.000 [0.000] 6:13 PM Move out of range: 562.794 247.444 30.000 [0.000] 6:13 PM Move out of range: 562.794 247.444 30.000 [0.000] So I then run INCREASE_Y_MAX per the guide and copy new info into printer.cfg. I am ran and done this like 40 times now with values changing but still get error when click the square.
What am I missing here?
6:13 PM Move out of range: 562.794 247.444 30.000 [0.000] 6:13 PM Move out of range: 562.794 247.444 30.000 [0.000] 6:13 PM Move out of range: 562.794 247.444 30.000 [0.000] So I then run INCREASE_Y_MAX per the guide and copy new info into printer.cfg. I am ran and done this like 40 times now with values changing but still get error when click the square.
What am I missing here?
3 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/6/2025 in #ratos-support
RatOS 2.1 RC and VAOC issue.
So on to next issue. I am doing this guide. https://docs.ratrig.com/v-core-4-0/idex-commissioning. At step Initial vaoc calibration. When I click on the VAOC I just get this spinning Green circle. What should I start looking at for this?
32 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/5/2025 in #ratos-support
RatOS 2.1 RC3 issue with configurator and T1.
Ok what is going on here? So run configurator and tell it I have ATC Semitec 104GT-2 for T1, When boots works but temp wrong. I edit RatOS.cfg and change it there to PT1000 then in works.
Hotend
T0 Phaetus Rapido Plus UHF definition (from RatOS/hotends/rapido-plus-uhf.cfg)
[extruder]
max_extrude_only_distance: 200
nozzle_diameter: 0.6
heater_pin: toolboard_t0:PB13
sensor_type: PT1000
pullup_resistor: 2200
sensor_pin: toolboard_t0:PA3
min_extrude_temp: 170
min_temp: 0
max_temp: 350
pressure_advance: 0.03
[firmware_retraction]
retract_length: 0.5
T1 Phaetus Rapido Plus UHF definition (from RatOS/hotends/rapido-plus-uhf.cfg)
[extruder1]
max_extrude_only_distance: 200
nozzle_diameter: 0.6
heater_pin: toolboard_t1:PB13
sensor_type: PT1000
sensor_pin: toolboard_t1:PA3
min_extrude_temp: 170
min_temp: 0
max_temp: 350
pressure_advance: 0.03
10 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/1/2025 in #ratos-support
2024-07-27-RatOS-2.1.0-RC2 issues with moonraker
As soon as I do the updates to this via Update Manager moonraker stops working and can't access GUI.
261 replies
RRCRat Rig Community [Unofficial]
•Created by rmilyard on 1/1/2025 in #ratos-support
RatOS-2.1.0-RC2 issues with flashing Octopus and EBB MCUs.
I keep getting this error:
Warning: Version mismatch
The board is running version v0.12.0-268-g0844388d but you your pi is on version v0.12.0-268-g0844388d7. If you want to update your board click 'flash again' below.
7 replies