Igor
RRCRat Rig Community [Unofficial]
•Created by Igor on 11/7/2024 in #fix-my-printer
Unknown command:"EXCLUDE_OBJECT_START"
top thx
4 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 11/8/2024 in #german-support
Kann mir hier vieleicht jemand helfen
hat funktioniert danke👍
5 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 11/8/2024 in #german-support
Kann mir hier vieleicht jemand helfen
das wurde doch immer in die moonraker eingetragen, ist das neu ??
5 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 11/7/2024 in #fix-my-printer
Unknown command:"EXCLUDE_OBJECT_START"
is that new in the printer.cfg it always goes into the moonraker.cfg
4 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 8/12/2023 in #german-support
SKRAT V 1.0 TMC2209
firmaware auch schon 4 mela neu gemacht
8 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 8/12/2023 in #german-support
SKRAT V 1.0 TMC2209
jo alles 3 mal kontrolliert
8 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 8/12/2023 in #german-support
SKRAT V 1.0 TMC2209
ok muss isch schauen, brauch ich das cuh wenn ich die driver schon an einem skr2 am laufen hatte ??
8 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 5/27/2023 in #german-support
Adaptiv Bed Mesh
Funzt jetzt danke !! musste raspi neustarten warum auch imer
3 replies
RRCRat Rig Community [Unofficial]
•Created by wise-white on 5/27/2023 in #ratos-support
Adaptive Mesh and Orca Slicer
Got it working now thanks, had to restart raspi for whatever reason
18 replies
RRCRat Rig Community [Unofficial]
•Created by foreign-sapphire on 5/27/2023 in #ratos-support
Adaptive Mesh and Orca Slicer
test also the new mesh have used pam until now.
if the new acuh only scans a small area like pam, it always does the whole area for me
18 replies
RRCRat Rig Community [Unofficial]
•Created by quickest-silver on 5/10/2023 in #fix-my-resonance
Is this CoreXY Belt Tension Good or Bad???
x 2 peaks
6 replies
RRCRat Rig Community [Unofficial]
•Created by fascinating-indigo on 5/10/2023 in #fix-my-resonance
Is this CoreXY Belt Tension Good or Bad???
x is bed y ok
6 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 4/28/2023 in #german-support
Drucker geht bei Start auf Pause
genau
12 replies
RRCRat Rig Community [Unofficial]
•Created by ptegler on 3/15/2023 in #ratos-support
Measure_linear_vibrations_range ERROR!
hello marc, there are also instructions on how to interpret the graphs
108 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 5/9/2023 in #german-support
4028 Fan
jo gefühlt kommt das hin
13 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 5/9/2023 in #german-support
4028 Fan
das ding ist ne turbine !!
13 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 5/9/2023 in #german-support
4028 Fan
ich habe nen delta
13 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 5/9/2023 in #german-support
4028 Fan
a oke also nicht in der printer passt danke
13 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 5/9/2023 in #german-support
4028 Fan
danke balu habe ich gelesen, balu du hattest irgend wo mit den reaktionszeit was geschrieben wie funzt das genau? weil das ding brauch ne weil bis des auf turen kommt
13 replies
RRCRat Rig Community [Unofficial]
•Created by Igor on 5/9/2023 in #german-support
4028 Fan
habe normales kabelführung und ein octopus board, wie gesagt immer 0 rpm, habe da auch mit den werten tachometer_poll_interval und tachometer_ppr rum gespielt aber nix rote schrift und und 0 rpm
13 replies