Maverik
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/18/2024 in #fix-my-print
Under Extrusion on corners
I did use the 0.6. You can chose it in the wizard
6 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/17/2024 in #fix-my-printer
TMC 'stepper_y' reports error: GSTAT: 00000004 uv_cp=1(Undervoltage!)
thank you for your suggestions
12 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/17/2024 in #fix-my-printer
TMC 'stepper_y' reports error: GSTAT: 00000004 uv_cp=1(Undervoltage!)
guess bad driver on arrival
12 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/17/2024 in #fix-my-printer
TMC 'stepper_y' reports error: GSTAT: 00000004 uv_cp=1(Undervoltage!)
I did replace it with one from my V3 and it works now
12 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/18/2024 in #fix-my-print
Under Extrusion on corners
6 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/17/2024 in #fix-my-printer
TMC 'stepper_y' reports error: GSTAT: 00000004 uv_cp=1(Undervoltage!)
Swapped the first 2 and now I get this: Unable to read tmc uart 'stepper_x' register IFCNT
12 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/17/2024 in #fix-my-printer
TMC 'stepper_y' reports error: GSTAT: 00000004 uv_cp=1(Undervoltage!)
No. I set the kinematic center and I am able to move all axis few times and then I get it
12 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 9/17/2024 in #fix-my-printer
TMC 'stepper_y' reports error: GSTAT: 00000004 uv_cp=1(Undervoltage!)
12 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
I use 0.6 nozzle
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
guessed that the default profile should have some reference in it
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
well, default was 10 seconds and 100%
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
I did try prusaslicer also with the default settings and I have the same result
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
will try it and post result
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
ok
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
what about the moving speed? 🙂
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
will change it to 15% and bridge at 40
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
ok
29 replies
RRCRat Rig Community [Unofficial]
•Created by Maverik on 11/9/2023 in #fix-my-print
No bridging is possible
nozzle temp for petg I have it to 240 and I use prusament filament
29 replies