jannu198
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
Update. Found out that the real cause of problems was the thermistor pin on my btt octopus 1.1 so I switched it to another one and now it works flawlessly with old pullup resistanse of 4700
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
This might not be the ideal solution but i ended up changing the pull up resistance to 18kOhm and now it works fine. I checked with another thermometer and it’s accurate to a 1~2 degree C at printing temperature.
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
Alright I understand. Thank you!
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
I bought the rapido from ratrig.com
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
I do not have any temperature fluctuations or whatnot so I don’t think it would be a bad cable either.
Right?
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
Should i just somehow create an offset in firmware? What should i do?
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
Is this behavior common for failing thermistor or is this something else?
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
I took a thermometer (for measuring body temperature) and if i set the temp to 70C and thermometer says 40~41C feels like it has 28-30C offset.
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
Is it possible that something in printer config file is wrong?
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
Abs usually is extruded anything above 220C in my experience.
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
No I didn’t. Only thing i saw is that it won’t extrude till 270c according to the thermistor.
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 2/9/2024 in #fix-my-printer
extruder temp is reported wrong. phatus rapido uhf
As far as i tested, no. I set it to 250c to extrude abs, extruder struggled until increased the temp to 270.
19 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 8/28/2023 in #ratos-support
reverse extruder stepper motor
Fixed it, thank you
3 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 8/28/2023 in #fix-my-mesh
Pringles shaped bed?
Thank you very much. I was already worried i would have to rebuild the frame.
14 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 8/28/2023 in #fix-my-mesh
Pringles shaped bed?
Or is this fair enough?
14 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 8/28/2023 in #fix-my-mesh
Pringles shaped bed?
Is there anything else i should do?
14 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 8/28/2023 in #fix-my-mesh
Pringles shaped bed?
14 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 8/28/2023 in #fix-my-mesh
Pringles shaped bed?
Okay, did that. Currently running a new mesh
14 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 8/28/2023 in #fix-my-mesh
Pringles shaped bed?
is this better? should i do more?
14 replies
RRCRat Rig Community [Unofficial]
•Created by jannu198 on 8/28/2023 in #fix-my-mesh
Pringles shaped bed?
14 replies