Disappointed
Disappointed
RRCRat Rig Community [Unofficial]
Created by Steppe_Warrior on 8/20/2024 in #fix-my-print
And here we go again... first layer problem even with beacon3D
You can also try to set the first layer width to 0.5mm
80 replies
RRCRat Rig Community [Unofficial]
Created by Steppe_Warrior on 8/20/2024 in #fix-my-print
And here we go again... first layer problem even with beacon3D
Sounds annoying but you have nothing to lose except time if it works
80 replies
RRCRat Rig Community [Unofficial]
Created by Steppe_Warrior on 8/20/2024 in #fix-my-print
And here we go again... first layer problem even with beacon3D
Only for the first layer…
80 replies
RRCRat Rig Community [Unofficial]
Created by Steppe_Warrior on 8/20/2024 in #fix-my-print
And here we go again... first layer problem even with beacon3D
I had the same problems on my 500 until i had acceleration at 4000 and speeds of less than 60mm/s, then my problem was so minimal that it didn’t matter anymore
80 replies
RRCRat Rig Community [Unofficial]
Created by Steppe_Warrior on 8/20/2024 in #fix-my-print
And here we go again... first layer problem even with beacon3D
Including speeds and acceleration
80 replies
RRCRat Rig Community [Unofficial]
Created by Steppe_Warrior on 8/20/2024 in #fix-my-print
And here we go again... first layer problem even with beacon3D
Can u send us a pic of your settings for the first layer
80 replies
RRCRat Rig Community [Unofficial]
Created by Kälte Kiste on 3/1/2024 in #german-support
V-Core 3.1 Sensorless Homing instalation
Da hast du garantiert noch nicht sensorless statt endstops eingestellt
12 replies
RRCRat Rig Community [Unofficial]
Created by Kälte Kiste on 3/1/2024 in #german-support
V-Core 3.1 Sensorless Homing instalation
Denke das problem liegt bei den RatOS variablen in der printer.cfg
12 replies
RRCRat Rig Community [Unofficial]
Created by Kälte Kiste on 3/1/2024 in #german-support
V-Core 3.1 Sensorless Homing instalation
Hey, kannst du deine printer.cfg und sensorless config komplett reinschicken?
12 replies
RRCRat Rig Community [Unofficial]
Created by Kälte Kiste on 3/1/2024 in #german-support
V-Core 3.1 Sensorless Homing instalation
[stepper_y] endstop_pin: tmc2209_stepper_y:virtual_endstop position_min: 0 position_endstop: 0 homing_retract_dist: 0 "position_endstop:" "0" ist vorne und "500" wär bei mir hinten wo ursprünglich der Endstop war.
12 replies
RRCRat Rig Community [Unofficial]
Created by Bastii on 12/25/2023 in #german-support
Euclid Probe
Umso besser, kein Problem
7 replies
RRCRat Rig Community [Unofficial]
Created by Bastii on 12/25/2023 in #german-support
Euclid Probe
Meiner kann Probleme machen, je nach Euclid Version und berührt bei manchen die Probe nicht die Magnete und deshalb kommt deine fehlermeldung https://www.printables.com/model/663668-vcore-3-toolhead-euclid
7 replies
RRCRat Rig Community [Unofficial]
Created by Bastii on 12/25/2023 in #german-support
Euclid Probe
@Bastii Welchen Euclid Mount benutzt du? Und möchtest du deine printer.cfg noch reinschicken?
7 replies
RRCRat Rig Community [Unofficial]
Created by dependent-tan on 5/22/2023 in #german-support
Belt tension graph... was sind die nächsten Schritte?
Da kann ich mich auch nur anschließen! :chefkiss:
141 replies