fluffy
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
also might be this
22 replies
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
try messing with those
22 replies
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
it's most likely the y linear rails
22 replies
RRCRat Rig Community [Unofficial]
•Created by malcinator on 8/30/2024 in #fix-my-mesh
[Vcore 4 500] Struggling with this one.
Just use kapton tape if you're unhappy and really wanna mess with it
15 replies
RRCRat Rig Community [Unofficial]
•Created by malcinator on 8/30/2024 in #fix-my-mesh
[Vcore 4 500] Struggling with this one.
no reason to mess with it more though
15 replies
RRCRat Rig Community [Unofficial]
•Created by malcinator on 8/30/2024 in #fix-my-mesh
[Vcore 4 500] Struggling with this one.
most likely its the bed
15 replies
RRCRat Rig Community [Unofficial]
•Created by malcinator on 8/30/2024 in #fix-my-mesh
[Vcore 4 500] Struggling with this one.
Might be
15 replies
RRCRat Rig Community [Unofficial]
•Created by malcinator on 8/30/2024 in #fix-my-mesh
[Vcore 4 500] Struggling with this one.
it could be the y linear rails being more torqued to the extrusion in that place
15 replies
RRCRat Rig Community [Unofficial]
•Created by malcinator on 8/30/2024 in #fix-my-mesh
[Vcore 4 500] Struggling with this one.
you could try adjusting y linear rails but i think its just the bed shape
15 replies
RRCRat Rig Community [Unofficial]
•Created by malcinator on 8/30/2024 in #fix-my-mesh
[Vcore 4 500] Struggling with this one.
that range on a 500 is perfect
15 replies
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
I also had issues with the back, because the electronics enclosure extrusions were pushing on the y extrusions compressing the gantry
22 replies
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
Your bed might be good though, so check it with a straight edge, before you attempt any of that
22 replies
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
You can use kapton tape to get the range down
22 replies
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
My bed was pretty bent 0.5 range and i managed to unbend it very much (0.2) by standing and jumping on it, with my girlfriend on my back on the exact spot it was bent at🤣 (NOT RECOMMENDED) some people have used a rubber mallet and precise blows, but that's also not recommended.
22 replies
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
it might be the bed shape
22 replies
RRCRat Rig Community [Unofficial]
•Created by d0zer on 8/28/2024 in #fix-my-mesh
[v-core-3.1 500mm] can't get it under .2mm range
check the bed with a straight edge and a light
22 replies
RRCRat Rig Community [Unofficial]
•Created by EODesigns on 5/6/2024 in #fix-my-mesh
VC3.1 Enclosed 400 Back Corner Peak
and run a 3 point calibration between bed meshes and adjustment
16 replies
RRCRat Rig Community [Unofficial]
•Created by EODesigns on 5/6/2024 in #fix-my-mesh
VC3.1 Enclosed 400 Back Corner Peak
make sure to adjust correct corners..
16 replies
RRCRat Rig Community [Unofficial]
•Created by EODesigns on 5/6/2024 in #fix-my-mesh
VC3.1 Enclosed 400 Back Corner Peak
your adjustment likely made it a bit worse?
16 replies
RRCRat Rig Community [Unofficial]
•Created by EODesigns on 5/6/2024 in #fix-my-mesh
VC3.1 Enclosed 400 Back Corner Peak
wasn't your previous mesh 0.2
16 replies