DJGummikuh
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 2/3/2024 in #fix-my-printer
Heatbreak/Coldend Clog
ok nevermind, I just killed my hotend 🤬️
5 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 2/3/2024 in #fix-my-printer
Heatbreak/Coldend Clog
huh. ok I reassembled everything but can't feed filament. wtf
5 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 2/3/2024 in #fix-my-printer
Heatbreak/Coldend Clog
5 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 2/3/2024 in #fix-my-printer
Heatbreak/Coldend Clog
I just noticed I can screw the heater and heatbreak from the coldend, I will do that, hopefully it allows me to access the coldend properly
5 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
however, I actually pointed a desk fan at the printer to reduce the temperature of the air in front of the hotend fan, to no measurable avail
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
After drying my filament for 6 hours today and still having the issues I finally shoved a thermal probe into the hotend and it appears that the cooling is not good enough. The entry into the heatbreak is exceeding 50°C, which is too much for the silk filament to stay solid
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
however, I limited now cooling to 50% (against my gut feeling, I think this needs as much cooling as it can get) but it actually does not show any difference whatsoever
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
I also evaluated the Fan speed, seeing that it started locking up in the first layer that has full cooling
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
Set retraction to 0.2 (from 0.5) and had exactly the same issues again
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
ok it's not retraction.
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
valid point
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
mh
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
but yeah I also assumed it might be a reason, can't really go lower though
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
tested from 0.2mm in 0.1mm steps
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
I just redid retraction, if I go below 0.5mm I have stringing
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
fan is nailed at 100% for everything except the first layer.
I'm using a nozzleX which is nickel plated steel iirc
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
as you can see at the bottom right the same speed CAN produce good results. until it doesn't
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
outside of these spurious occasions where EVERYTHIGN clacks
54 replies
RRCRat Rig Community [Unofficial]
•Created by DJGummikuh on 8/12/2023 in #fix-my-print
Silk PLA causes repeating clogging during printing
also, earlier I was printing infill with 240mm/s without clacking
54 replies