Hydr0s
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 11/25/2024 in #fix-my-printer
Tool head errors when going Hybrid to IDEX
Did you do a complete reflash of the sd, or is there a way to do it without re flashing the sd card
8 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 11/25/2024 in #fix-my-printer
Tool head errors when going Hybrid to IDEX
I’ll give that a shot
8 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 11/25/2024 in #fix-my-printer
Tool head errors when going Hybrid to IDEX
Okay, thanks
8 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/31/2024 in #fix-my-printer
TMC 'extruder' reports error: GSTAT: 00000001 reset=1(Reset)
think the fix was a dogy cable
9 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/31/2024 in #fix-my-printer
TMC 'extruder' reports error: GSTAT: 00000001 reset=1(Reset)
9 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/24/2024 in #fix-my-print
Consistent gaps between walls with proper EM and PA on VC4-400 hybrid.
Lowest top left, highest top right
15 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/24/2024 in #fix-my-print
Consistent gaps between walls with proper EM and PA on VC4-400 hybrid.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/24/2024 in #fix-my-print
Consistent gaps between walls with proper EM and PA on VC4-400 hybrid.
Forgot to mention my current en for this filament is 0.86
15 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/24/2024 in #fix-my-print
Consistent gaps between walls with proper EM and PA on VC4-400 hybrid.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/24/2024 in #fix-my-print
Consistent gaps between walls with proper EM and PA on VC4-400 hybrid.
Flow rate as in max flow or EM?
15 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/24/2024 in #fix-my-print
Consistent gaps between walls with proper EM and PA on VC4-400 hybrid.
0.04 standard, if I bump em then top surfaces become majorly over extruded
15 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/16/2024 in #fix-my-printer
"No beacon model loaded" error (V4 400 Hybrid)
as long as i keep my custom overrides file safe then it shouldn't be too much of a hastle
14 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/16/2024 in #fix-my-printer
"No beacon model loaded" error (V4 400 Hybrid)
but then i got the same error on the poke test
14 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/16/2024 in #fix-my-printer
"No beacon model loaded" error (V4 400 Hybrid)
okay, so just ran it and it worked
14 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/16/2024 in #fix-my-printer
"No beacon model loaded" error (V4 400 Hybrid)
didn't work
14 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/16/2024 in #fix-my-printer
"No beacon model loaded" error (V4 400 Hybrid)
already done, really dont want to but im considering just restarting from fresh
14 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 8/16/2024 in #fix-my-printer
"No beacon model loaded" error (V4 400 Hybrid)
already have wont even perform the initial calibration
14 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 7/20/2024 in #fix-my-printer
very inconsistent first layers on VC4
I’ll double check tonight, I’m printing pla at the moment as my panels only just arrived, but when I get them on I’ll be moving to and for the most part
11 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 7/20/2024 in #fix-my-printer
very inconsistent first layers on VC4
Both Benchys are printed in the center of the bed, so it's not a height map issue, as the bed is probed at the start of each print. The problem is definitely with the nozzle when bits of filament hanging out trigger the beacon contact. If I manually clean the nozzle before each print, I get a perfect first layer.
What I'm looking for is a way for the printer to either raise the nozzle temperature while performing the beacon contact to determine the correct Z-height at the start of a print, so any filament on the tip melts. Alternatively, I can design a wiper with a brass brush that raises the nozzle temperature to 150°C and drags it across the nozzle to clean it before performing a beacon contact.
11 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 7/20/2024 in #fix-my-printer
very inconsistent first layers on VC4
Heat soaking won’t be a factor here
11 replies