manofthesky
RRCRat Rig Community [Unofficial]
•Created by C7H on 1/21/2024 in #fix-my-mesh
Frame Adjustment advice
How did you manage the back extrusions ?
27 replies
RRCRat Rig Community [Unofficial]
•Created by continuing-cyan on 11/2/2023 in #fix-my-mesh
Saddle shape mesh (V-Core 3.1 500mm)
hey,
How did you manage to lower the back extrusions ? i couldn't seem to be able to do it. Thanks
12 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/29/2023 in #fix-my-printer
Ratrig Bedmesh looking aweful
Well i hope i will be able to do the same with the 500, thank you for the help fritz !
13 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/29/2023 in #fix-my-printer
Ratrig Bedmesh looking aweful
Thank you, any jigs that could help ?
13 replies
RRCRat Rig Community [Unofficial]
•Created by eastern-cyan on 6/26/2023 in #fix-my-mesh
Idea? Bedmesh is completely off world
did you manage to fix it ?
4 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
It’s talking about 25hz and 100hz. Now it is correct
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
Not sure about the fan, i didn't see a difference in the 25hz compared to the 100hz
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
Well everything is working
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
i need to swap the Z cause it's going the opposite direction
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
You are the best thank you !!
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
I HAVE MOVEMENT
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
yes
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
Well at 0% it's at 100%
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
it was a jumper issue, now the fan is working
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
Well all my driver, not only X
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
Oh do i need to remove this jumper ? The 24v delivery is checked. It is correctly wired
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
Tmc 2209
32 replies
RRCRat Rig Community [Unofficial]
•Created by manofthesky on 11/11/2023 in #ratos-support
Problems with printer.cfg
So all my drivers are connected to the octopus v1.1 and all the pins are set correctly on the board , i can't move the printer for some reasons, i do not know why
32 replies