audiorazor
RRCRat Rig Community [Unofficial]
•Created by audiorazor on 10/21/2023 in #fix-my-printer
Nasty hot end collision and now I'm getting this on my bed meshes.
hopefully someone has some insight.
4 replies
RRCRat Rig Community [Unofficial]
•Created by audiorazor on 10/21/2023 in #fix-my-printer
Nasty hot end collision and now I'm getting this on my bed meshes.
its roughly 1mm high on the rear motor.
4 replies
RRCRat Rig Community [Unofficial]
•Created by audiorazor on 10/21/2023 in #fix-my-printer
Nasty hot end collision and now I'm getting this on my bed meshes.
also, why wouldnt z tilt fix this
4 replies
RRCRat Rig Community [Unofficial]
•Created by Dante Tango on 9/27/2023 in #fix-my-print
Surface Artifacts
200 is also really low for those speeds. might want to try and bump the temps up
19 replies
RRCRat Rig Community [Unofficial]
•Created by Beluga on 9/1/2023 in #ratos-support
extruder rotating in opposite direction
3 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
agreed
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
within reason of course.
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
1mm made all the difference
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
yea mine were knocking into the prints
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
yea but matt has said it can be further away with no negative impact
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
I talked to the beacon people and they said it only came with 1 type of screws
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
I found that was too tight and I was actually hitting my prints
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
I remixed that duct and raised it so you have more clearance.
130 replies
RRCRat Rig Community [Unofficial]
•Created by Silver Raider US on 7/15/2023 in #ratos-support
Beacon Help
which duct are you using that its mounted to?
130 replies
RRCRat Rig Community [Unofficial]
•Created by VanOfHoogen on 6/28/2023 in #fix-my-print
Troubleshooting benchy (heat issues)
should be 100%
11 replies
RRCRat Rig Community [Unofficial]
•Created by VanOfHoogen on 6/28/2023 in #fix-my-print
Troubleshooting benchy (heat issues)
and what percent of fan?
11 replies
RRCRat Rig Community [Unofficial]
•Created by VanOfHoogen on 6/28/2023 in #fix-my-print
Troubleshooting benchy (heat issues)
what fan are you using?
11 replies
RRCRat Rig Community [Unofficial]
•Created by VanOfHoogen on 6/28/2023 in #fix-my-print
Troubleshooting benchy (heat issues)
what material?
11 replies
RRCRat Rig Community [Unofficial]
•Created by DemetriKarakashev on 6/26/2023 in #fix-my-printer
Temperature fluctuates by 1.5 degrees.
did you run a pid tune?
5 replies