Talannvor Comments - Answer Overflow

Talannvor

•Created by LynX83 on 7/7/2024 in #fix-my-printer

new vcore-3.1 500 do not extrude whit LGX and rapido phateus v2

looks like maybe heat creep, but yeah first thing to check is your cooling fan is pushing air into the hotend i.e. label toward heatsink, and that it is set to 100%

8 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 5/24/2024 in #fix-my-printer

Extruder reset error only after 3+ hours of printing

also check your run amperage if you have modified anything in the configs

15 replies

RRCRat Rig Community [Unofficial]

•Created by BeardedCobra48 on 3/2/2024 in #fix-my-printer

printer Smoking ☹

just make sure to remove it before you start printing.

268 replies

RRCRat Rig Community [Unofficial]

•Created by BeardedCobra48 on 3/2/2024 in #fix-my-printer

printer Smoking ☹

thats the host, mcu is wacko but i dont trust it till its "running"

268 replies

RRCRat Rig Community [Unofficial]

•Created by BeardedCobra48 on 3/2/2024 in #fix-my-printer

printer Smoking ☹

what you purchased wasnt a PT1000 - did you add one in after the fact? - sorry realized that was someone elses statement. (ts 6am i should go to bed)

268 replies

RRCRat Rig Community [Unofficial]

•Created by BeardedCobra48 on 3/2/2024 in #fix-my-printer

printer Smoking ☹

ADC is a type of pin essentially: https://www.klipper3d.org/FAQ.html#do-i-have-to-wire-my-device-to-a-specific-type-of-micro-controller-pin

268 replies

RRCRat Rig Community [Unofficial]

•Created by BeardedCobra48 on 3/2/2024 in #fix-my-printer

printer Smoking ☹

the MCU will throw errors if you dont have a temp probe attached to the hotend and heated bed pins, this is a safety feature to ensure you do not have thermal runaway/fire. essentially once you attach those, it should start enough to see whats going on (if anything is)

268 replies

RRCRat Rig Community [Unofficial]

•Created by BeardedCobra48 on 3/2/2024 in #fix-my-printer

printer Smoking ☹

i mean i see the graphic for it, if that is the question.

268 replies

RRCRat Rig Community [Unofficial]

•Created by BeardedCobra48 on 3/2/2024 in #fix-my-printer

printer Smoking ☹

that is likely wrong, unless the MCU is smoking.

268 replies

RRCRat Rig Community [Unofficial]

•Created by matt707_ on 3/9/2024 in #fix-my-printer

Problem Homing X and Y

glad you foun d it

5 replies

RRCRat Rig Community [Unofficial]

•Created by matt707_ on 3/9/2024 in #fix-my-printer

Problem Homing X and Y

if you can move the carriage by hand easily to the left and right front and back (do this slowly), then likely you need to do two things, first is check your wiring for the steppers, making sure your coils are not crossed, if you are sure the coils are hooked up correctly (the stock wires if you bought a kit should be fine) then you may need to up the voltage on your steppers (but this should be the last change to do to start)

5 replies

RRCRat Rig Community [Unofficial]

•Created by BeardedCobra48 on 3/2/2024 in #fix-my-printer

printer Smoking ☹

you can temporarily set the min and max temperatures to get the dashboard up, but i agree to attach the thermistors for bed and hotend. (also if you do this make darn certain to remove the temporary changes of -300 etc

268 replies

RRCRat Rig Community [Unofficial]

•Created by dunkeluk on 3/9/2024 in #fix-my-print

Terrible Extrusion Inconsistency On New V-core Build

yup good that you found it, but essentially if you have what looks like thin layers its skipping on the filament or cant push it hard enough, one of the two almost all the time, or a bad setting for thermistor. any which way glad you found it.

11 replies

RRCRat Rig Community [Unofficial]

•Created by dunkeluk on 3/9/2024 in #fix-my-print

Terrible Extrusion Inconsistency On New V-core Build

could be many different issues but appears to me to be under extrusion which can stem from flow rate (meaning not able to melt as fast as you are asking it to), nozzle blockage, reverse bowden etc. i am seeing breaks in the skirt as well which should not be, are you hearing any skipped steps from the extruder motor?

11 replies

RRCRat Rig Community [Unofficial]

•Created by MichaelKnight on 1/21/2024 in #fix-my-printer

Z homing issue

(tool changers)

106 replies

RRCRat Rig Community [Unofficial]

•Created by MichaelKnight on 1/21/2024 in #fix-my-printer

Z homing issue

we should probably move this from the help thread, but yeah it just has to re-prime the tools dealing with drips etc, so it doesnt put horrible blobbies on the prints

106 replies

RRCRat Rig Community [Unofficial]

•Created by MichaelKnight on 1/21/2024 in #fix-my-printer

Z homing issue

just less so than bambu etc

106 replies

RRCRat Rig Community [Unofficial]

•Created by MichaelKnight on 1/21/2024 in #fix-my-printer

Z homing issue

i mean, any mmu will be like that, and even tool changers will need purge/extra filament

106 replies

RRCRat Rig Community [Unofficial]