Chrizzar
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/28/2024 in #ratos-support
Realtime Analysis - SciChart too old.. error
Thank you Mikkel.
I will check tomorrow if I have time.
It has been a hard and busy last week..
43 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/28/2024 in #fix-my-printer
Weird sound from belts.. can’t find the cause
Yup, thanks 🙂
10 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/28/2024 in #fix-my-printer
Weird sound from belts.. can’t find the cause
The sound dissappeared for some reason now that the printer has been heat soaking for awhile
10 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/28/2024 in #fix-my-printer
Weird sound from belts.. can’t find the cause
Quite cool that I you can hear it more quickly that way
10 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/28/2024 in #fix-my-printer
Weird sound from belts.. can’t find the cause
Don’t know yet.
10 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/28/2024 in #fix-my-printer
Weird sound from belts.. can’t find the cause
I know that you don't like guessing, but could it be the bearings in the left X holder?
10 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/28/2024 in #ratos-support
Realtime Analysis - SciChart too old.. error
@miklschmidt
43 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/28/2024 in #ratos-support
Realtime Analysis - SciChart too old.. error
43 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/27/2024 in #fix-my-printer
Frequent Issue - MCU 'mcu' shutdown: Timer too close
Actually the Beacon is attached to the Raspi Pi
15 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/27/2024 in #fix-my-printer
Frequent Issue - MCU 'mcu' shutdown: Timer too close
Ahh okay
15 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/27/2024 in #fix-my-printer
Frequent Issue - MCU 'mcu' shutdown: Timer too close
Console? What is this?
15 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 12/27/2024 in #fix-my-printer
Frequent Issue - MCU 'mcu' shutdown: Timer too close
This is what I have connected to my
Raspberry Pi 4 8GB RAM with
MicroSD Card 64gb V10 / U10:
- Klipperscreen.
- No webcam attached.
- Beacon rev h
- BTT Octopus V1.1 with attached:
* P1000 for the goliath hotend.
* BTT SFS 2.0.
* CPAP fan.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 10/9/2024 in #fix-my-mesh
Is this a problem with the bed itself or the frame? (V-Core 3.1 500)
Ahh ok good thinking.
Let me check
19 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 10/9/2024 in #fix-my-mesh
Is this a problem with the bed itself or the frame? (V-Core 3.1 500)
Would you think it would be better if I removed half of them and then re-torqued them to 1Nm?
19 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 10/9/2024 in #fix-my-mesh
Is this a problem with the bed itself or the frame? (V-Core 3.1 500)
RatRig pei.
19 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 10/9/2024 in #fix-my-mesh
Is this a problem with the bed itself or the frame? (V-Core 3.1 500)
However, should it now only be half of them and not all?
19 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 10/9/2024 in #fix-my-mesh
Is this a problem with the bed itself or the frame? (V-Core 3.1 500)
Pretty much as shown in the guide
19 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 10/9/2024 in #fix-my-mesh
Is this a problem with the bed itself or the frame? (V-Core 3.1 500)
Every second, from one end to the other. Then the rest back.
19 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 10/9/2024 in #fix-my-mesh
Is this a problem with the bed itself or the frame? (V-Core 3.1 500)
Ok cool cool thx 🙂
I used a torque screwdriver from Wera to screw them all with same torque at around 1 Nm..
But I can ofc try again..
19 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 6/10/2023 in #fix-my-printer
Keep getting MCU error with Goliath hotend attached.
Is there a way to say that this issue is closed?
11 replies