Campapalooza
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
That's fair. Pre-IDEX, my ABS profiles were pretty decent, but maybe something else has changed. It's on my list to give that a shot. Thanks!
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
But I plan to look into that more this weekend...hopefully
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
Haven't even messed with IS yet but this is on my hopefully this weekend. Never felt like I could fully get the hybrid belts to the point where they a) weren't floppy and b) didn't makes my graphs look less than ideal on hybrid to begin with so I'm not holding out a ton of hope that they don't look rough on IDEX lol
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
Haven't yet tried PLA just cause ABS is what I already had loaded when I started messing with this. It is on my list, but honestly I've been delaying it because accepting "I can only do PLA" is less than ideal even if it were to work lol
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
Another benchy attempt, again at a (crazy slow) 100mm/s & 2k....trying to burn everything back to the ground and see if this thing is even capable of giving a reasonable quality print 😔
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
It might be a harder test, but the prints I'm getting so far make it seem impossible, which it shouldn't be.... especially at very very slow speeds
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
Well feel free to keep me posted, and I'll do the same if I make any breakthroughs. Not holding out major hope at the moment though sadly
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
Sorry, yes. It unfortunately did not. Let's just say the possibility of un-idex'ing this thing is still definitely not outside the realm of possibility.
Even slowing printing down to ~100mm/s and 2k accel is still pretty awful. About the only thing I haven't tried yet is pulling the spools off of their holders inside the printer, and just putting them on some super smooth rollers to eliminate any form of resistance from the possibility list
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/19/2025 in #fix-my-print
Weird Artifacts when layers get small & fast
Interesting...they're definitely snug so I will give that a shot thank you.
18 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/2/2025 in #ratos-support
Anyone have a completely working Nginx Reverse Proxy config by chance?
Gotcha
6 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 2/2/2025 in #ratos-support
Anyone have a completely working Nginx Reverse Proxy config by chance?
Ok. I'm far from an expert but I have enough self hosted services set up that doesn't a huge portion of software that has a web UI utilize either Apache or Nginx? I'm confused as to why that would break just a single page when 95% of it works perfectly.
The only clue I've seen so far was a console error that indicated the secure websocket connection couldn't be opened over a non-secure connection. Which would make sense since even though browser to RP is public trusted CA cert encrypted, the connection between the RP and RatOS is only HTTP.
That all makes me think I could easily fix if by serving RatOS over HTTPS (just with a basic self signed cert) but I don't suppose there's an easy way to do that without diving deep into each individual RatOS host I have right?
6 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 11/24/2024 in #fix-my-print
Strange infill separation problem after pretty good first layer
Yeah appreciate the advice - I had the same issue with my third test print to make sure things were working before I tried a fresh roll. I’m not entirely sure what the issue was, but for sake of completeness this issue seems to have resolved itself for me after releveling and increasing my line widths a smidge. Thanks all!!
17 replies
RRCRat Rig Community [Unofficial]
•Created by Campapalooza on 11/24/2024 in #fix-my-print
Strange infill separation problem after pretty good first layer
Thanks for the response! I honestly haven’t printed a single part that’s this big on it in a long long time, but no other “normal” sized prints I haven’t seen this issue with. I did try slicing it at 0.3 rather than the 0.2 I usually use however. I also don’t see any signs of clogging either when it’s happening…the extruder is definitely not skipping.
I think I’m going to try playing with the line width and see if putting down just a little more plastic will help those line edges adhere to each other better…at least that’s where my head is currently at.
17 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
Appreciate the help!
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
Got it printing now so hopefully that'll fix that error for me
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
I swear that part wasn't even not in deprecated nearly two months ago when I started printing my parts but maybe I'm wrong it's happened before lol
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
@chicken yeah makes sense. I've got some other stuff attached to mine so I don't plan to even put the cover on honestly...clearly I haven't been paying enough attention didn't even realize there was a 120mm fan version already out lol
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
Nvm. vc4_electronics_duct.stl. In the 'deprecated folder. That would be why I didn't even print it smh lol
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
Any idea what this piece is called? I'm hitting the same overheat error and apparently failed to even print this part lol
376 replies