VisualTech48
RRCRat Rig Community [Unofficial]
•Created by Sky on 11/8/2024 in #fix-my-mesh
Commissioning Mesh - Looking for assistance
Also you dont really gain that much as the acceleration suggestions are mostly for the outer walls.
33 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 11/8/2024 in #fix-my-mesh
Commissioning Mesh - Looking for assistance
It won't be perhaps much of an issue if you don't go high temp and enclosed but becqon contact has been known to have inconsistentcies with those.
33 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 11/8/2024 in #fix-my-mesh
Commissioning Mesh - Looking for assistance
It will for sure. @dickpoop and we've seen issues with becqon contact as well
33 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 11/8/2024 in #fix-my-mesh
Commissioning Mesh - Looking for assistance
@dickpoop basicly just to prove the point. That means that your middle dipped during time.
The issue is to fully fix it you either loosen the rail, put your bed onto what you usually print with then tighten the bolts so the dip is only present when it's cold.
Or get a titanium tube from @Mike-Toro3D and not worry much about changing temperatures.
33 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 11/8/2024 in #fix-my-mesh
Commissioning Mesh - Looking for assistance
You might suffer from it when its hot
33 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 11/8/2024 in #fix-my-mesh
Commissioning Mesh - Looking for assistance
Yeah its just how it is with a big machine, also look at bi-metalic.
33 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Perhaps you rushed it at the end and gg
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
😄
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
You just need a flat surface where you will assemble it
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
No need for a 134 euro bracket.
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
You can all do it by hand really.
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Before even going to everything else.
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
THat is why you usually wanna get that solid
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
But this kind ahole on the frame is not ideal square wise.
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Yeah but you could've adjusted the printed parts to be a bit depper for that
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Yeah that is not ideal in my opinion at least.
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Can you chime in here?
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
@miklschmidt
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
0.2 is a kinda in that range of perhaps you should fix it. But I'm no expert there.
680 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 11/13/2024 in #fix-my-print
Inconsistent Flow on each print/ day
Basicly yeah
680 replies