stylax
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/13/2025 in #fix-my-printer
Am I screwed?
sadness, okay, thank you for the quick response @Mitsuma :ratrig_heart:
5 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/13/2025 in #fix-my-printer
Am I screwed?
bruh 😦
5 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
being past 4 on PSD seems a tad, over
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
it does it on both the X and Y movements during IS, it sounds like it's coming from the hotend assembly
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
the motion is great, everything is lined up - it's just this noise during certain movements
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
shall i turn off perf mode for now then and see what is what?
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
i do want to note that this is on performance mode also, so 1.6 on the motors
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
@TheTik - i cleaned the x and y rails, re-greased them and it's still doing it 😦
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
they're slightly smoother in the middle of the rail, slightly less so towards the top and bottom of the rail
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
i greased them about a month or so ago
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
but i'm thinking if i take the tension off, or realign the gantry, they may be smoother?
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
a tad stiff, and they sound a little crunchy
21 replies
RRCRat Rig Community [Unofficial]
•Created by stylax on 4/12/2025 in #fix-my-printer
Can't figure out why this noise exists...
@TheTik - out of line? should i redo the gantry alignment ?
21 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/17/2024 in #fix-my-resonance
is this a okay graph?
See what input shaper graphs say and send it
18 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/17/2024 in #fix-my-resonance
is this a okay graph?
are you hearing anything rattling whilst it's doing the shaking? this has a lot of spikes, 2 is fine and a smaller one but this one is a bit wild! check your belts are sitting in the idlers, loose bolts, anything around the electronics that might be loose and causing vibrations
18 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/17/2024 in #fix-my-resonance
is this a okay graph?
18 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/17/2024 in #fix-my-resonance
is this a okay graph?
this second peak might be worth looking at, as you want the shaper graphs to be a single peak and it should settle down towards the higher freqs
18 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/17/2024 in #fix-my-resonance
is this a okay graph?
if you're running RatOS 2.1, you can run the frequency analyser around the 30hz mark and find out what's causing that first peak if you're worried.
18 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/17/2024 in #fix-my-resonance
is this a okay graph?
then run your input shaper commands and see what pops out
18 replies