Daxxer
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow

16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow
for anyone in the future, there were multiple things wrong that caused this.
the frist I think were the bolts holding down the rails. I think some of the bolts were actually slipped inbetween the 3030 and not actually holding down the rail.
secondly, I actually ended up buying a torque wrench off amazon for $50 to make sure I had even pressure on the rails.
3rdly, my frame was not square so I borrowed my wife's 91cm ruler and did my best to make sure all the corners were the same height.
16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow
tyvm @polyhedra_ and @Ross13 for the help!
16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow

16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow

16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow
now i'm really considering purchasing a torque wrench. Any chance you could tell me how much Nm is recommended for the screws on the rails?
16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow

16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow
I home, z-tilt then run the mesh. Also, solved my belt binding issue somewhere in the middle while taking things apart
16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow

16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/20/2024 in #fix-my-resonance
VC3.1 500. I am getting some belt binding
sorry for being a nub but would you mind explaining why that maters? I'd like to know for whenever I do enclose the printer
9 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/11/2024 in #fix-my-mesh
VC3.1 500. From Saddle to bow

16 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/20/2024 in #fix-my-resonance
VC3.1 500. I am getting some belt binding
it is not
9 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 6/25/2023 in #fix-my-mesh
Probed after heating shows upwards bow down the center

11 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 6/25/2023 in #fix-my-mesh
Probed after heating shows upwards bow down the center
sorry but i'm a bit confused as to what your bed support does. Does it eliminate the need for the rear z point at the back of the bed? those custom supports look like they are supporting the bed from the front.
I am also not sure how this would help with the bulge due to heat.
11 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 6/25/2023 in #fix-my-mesh
Probed after heating shows upwards bow down the center
I was able to get under 0.2 with a cold bed. Is that not possible with a bed of this size when heated?
11 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 6/25/2023 in #fix-my-mesh
Probed after heating shows upwards bow down the center
it is the 500mm vcore 3
11 replies