Valaria
RRCRat Rig Community [Unofficial]
•Created by Valaria on 1/14/2025 in #fix-my-printer
Y linear rails offset or profile twisted
5 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 1/14/2025 in #fix-my-printer
Y linear rails offset or profile twisted
Yes, I measured the profiles as best I could. I don't have any professional equipment, just a caliper, some squares and steel measures. Here's what I noticed. The corner plates are not completely flat. When I look at the aluminum profiles with a small angle, in many profiles the groove is curved outwards. I place the profiles on one level and connect them to the corner plates. It's absolutely rectangular. But as soon as I attach a profile at a 90 degree angle perpendicular to it, it is pulled outwards or inwards through the sheets. Maybe even twisted. In order to get an angle at the top of the front to align the X-axis, I have to screw the idler sheets and push the Profiles with my hand so that it becomes an angle. With all the sheets for idlers and engines, I see that if they are attached to one profile and I screw them to the other, she pulls it to the other profile. This means that they never laying plane completely, but are pulled upwards. I also suspect that if I prepare the front, rear and frame for the electronics as in the RatRig instructions, the corner plates will warp the profiles.
5 replies
RRCRat Rig Community [Unofficial]
•Created by thanksihateit on 12/23/2024 in #ratos-support
Octopus V1.1 detected but is unresponsive.
Do you set the BOOT jumper, press reset, after remove the jumper press flash button?
18 replies
RRCRat Rig Community [Unofficial]
•Created by Digger738 on 12/20/2024 in #ratos-support
No Belt Tension Graphs
@miklschmidt What update? All RatiOS components are actual and cannot be updated.
67 replies
RRCRat Rig Community [Unofficial]
•Created by Digger738 on 12/20/2024 in #ratos-support
No Belt Tension Graphs
67 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
Yes, I can. I rewrote the SD image again. Then pressed "Update all" in the mainsail. After that, my Moonraker is broken and cannot be repaired. Index file broken. Wrong URL, etc. Connection to the printer board doesn't work either. Now recreate the SD card again.
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
Now i a fresh copy of RatOS 2.1. After all updates, the configurator not working. 502 Bad Gateway nginx/1.18.0
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
Thanks for now. I'll look into it again later when my head is clearer.
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
That sounds good if you can change the corner for the blob. I'm German. And if everything was in English everywhere, I could jump in circles. I can read through it all, but you can't really ask someone who can really explain it to you properly.
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
When I press Home, X moves to zero, then to the middle of the bed, then it moves to Y zero, back to the middle, briefly moves the head back and forth 1 centimeter, then it does Z zero. Z_Hop moves up 10mm and then much further down. With Prime_Blob, it doesn't move to the left corner at the front X zero like it used to, but across the bed to the right corner. The direction of travel of the motors wasn't right either. I adjusted that.
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
I used the configurator. But after the new printer.cfg went completely crazy, I used my old printer.cfg. I absolutely don't like how everything is scattered in files in RatOS 2.1. What was always annoying was the SPI3 error message. I can't get rid of it. SPI3 is set in the board file. With the original homing, the Printer always moves around unnecessarily. And the Z axis is always moves down to who knows what. Prime_Blob is now also on the other corner of the bed. I really don't see any advantages for me in RatOS 2.1.
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
Sorry. The other way around. The error did not occur with the files. But now again
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
Wrong thought. When I restarted the printer for the Debug.zip for you, the error occurred. I turned it off again and restarted it. Now this error message did not appear. So it occurs sporadically
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
Here the archive. This was a reboot without errors🙄
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
Ok. I will try in some minutes. My printer print now
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
Ahhh😃
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
I cant findit
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
You mean the logfiles?
43 replies
RRCRat Rig Community [Unofficial]
•Created by Valaria on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
RatOS is up to date. Only RatOS Configurator repository update failures
43 replies