Backyarder
RRCRat Rig Community [Unofficial]
•Created by Backyarder on 12/19/2024 in #fix-my-printer
new ratos update, now cannot print
updated, received error when trying to print after update. Reflashed firmware thinking maybe there is a mismatch somewhere, updated then re-did config. Still getting the same error msg. Restored old image and it prints fine. I think it's a bug with the new update.
10:15 PM
Welcome to RatOS v2.1.0
v2.1.0-RC3-15-g6aa3c1b8
Unhandled exception during run
10:14 PM
Unhandled exception during run
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
10:14 PM
Unhandled exception during run
10:14 PM
Unhandled exception during run
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
10:14 PM
Unhandled exception during run
10:14 PM
Unhandled exception during run
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
10:14 PM
Unhandled exception during run
10:14 PM
Unhandled exception during run
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
10:14 PM
File selected
10:14 PM
File opened:3DBenchy_0.25mm_PETG_20m38s.gcode Size:2211882
10:14 PM
Klipper state: Shutdown
10:14 PM
Post-processing unsuccessful
File is not supported, aborting...
10:14 PM
Post-processing started
Processing 3DBenchy_0.25mm_PETG_20m38s.gcode (2.11 mb)...
10:14 PM
SDCARD_PRINT_FILE FILENAME="3DBenchy_0.25mm_PETG_20m38s.gcode"
10:07 PM
SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=80
10:04 PM
SET_FAN_SPEED FAN=Raspi_Fan SPEED=1
4 replies
RRCRat Rig Community [Unofficial]
•Created by Backyarder on 12/11/2024 in #fix-my-printer
cannot connect to pi ip.
after no success with 2 weeks of attempted calibration and vaoc led stopped working i thought id start again. Flash sd card. Now not connecting via ethernet ip. Can only connect to pi via ratos.local network. Thus no internet and no updates and no config. Tried 3 x diff sd cards. Put old install sd card back in and works. Tried diff raspi still no go. WTF is wrong with this stupid thing? :need: Cheers.
56 replies
RRCRat Rig Community [Unofficial]
•Created by Backyarder on 12/9/2024 in #fix-my-printer
btt 2240 v1 drivers giving error.
Unable to write tmc spi 'stepper_z' register DRV_CONF
How do i make these work?
RATOS config changed but still not working. ( dont understand why a config program doesn't config).
Lots of posts about 2240's but no fixes posted.
How did you get them to work?
Help appreciated. Thanks.
9 replies
RRCRat Rig Community [Unofficial]
•Created by Backyarder on 12/2/2024 in #fix-my-printer
ORBITOR FILAMENT SENSOR
vcore4 idex, hooked up orbitor filament sensors on each toolhead. T0 seems to work and heats the nozzle and loads the filament. But T1 doesnt. Just showing green light, without filament, and blinks blue when i push button but nothing happens. I got the code from github and for T1 i just used the example of T0 but changed it to T1. file attched if anyone has time to check it out. cheers
18 replies
RRCRat Rig Community [Unofficial]
•Created by Backyarder on 12/1/2024 in #ratos-support
RATOS bug?
6 replies