millenford - VC4 300h
millenford - VC4 300h
RRCRat Rig Community [Unofficial]
Created by millenford - VC4 300h on 9/12/2024 in #fix-my-print
Are there standard test print STL's beyond the ratrig commissioning first layer test print?
FYI: I use PrusaSlicer, but I discovered that OrcaSlicer has some good "built-in" test prints that I've used for testing. The Orca gcode causes RatOS to generate a couple of non critical errors in the console between each layer because I didn't take the time to edit/insert RatOS compatible gcode, but they generate good prints for testing. Marked as Solved.
17 replies
RRCRat Rig Community [Unofficial]
Created by millenford - VC4 300h on 10/7/2024 in #ratos-support
What causes "toolhead stopped below model range" and what can be done?
Sure is. I read that doc but failed to retain that part. thanks!
11 replies
RRCRat Rig Community [Unofficial]
Created by millenford - VC4 300h on 10/7/2024 in #ratos-support
What causes "toolhead stopped below model range" and what can be done?
Is this for real? Doing a specific RatOS update before the others? I've always done UPDATE ALL COMPONENTS. At any rate, after the last update I got a few real good first layer test prints. I even cycled power yesterday and it seemed to print good again after that. As a side issue, some "numbers" have gotten out of whack somewhere because of something I've done, and I drove the print bed into the nozzle (while at rest). That never happened before. To be honest, I'm afraid to power it up and try again today, but I will. It's all become superstition to me.
11 replies
RRCRat Rig Community [Unofficial]
Created by millenford - VC4 300h on 10/7/2024 in #ratos-support
What causes "toolhead stopped below model range" and what can be done?
No description
11 replies
RRCRat Rig Community [Unofficial]
Created by millenford - VC4 300h on 10/7/2024 in #ratos-support
What causes "toolhead stopped below model range" and what can be done?
11 replies
RRCRat Rig Community [Unofficial]
Created by archen on 6/5/2024 in #ratos-support
Toolhead stopped below model range
I searched for a solution to "toolhead stopped before model range" instead of posting first, and that search led me here. Trying my best.
18 replies
RRCRat Rig Community [Unofficial]
Created by archen on 6/5/2024 in #ratos-support
Toolhead stopped below model range
@Helge Keck Can I edit the "model range" numbers to prevent this error? I'm running RatOS 2.1 RC3, and have run the initial beacon cal, beacon_ratos_calibration, and beacon_create_scan_compensation_mesh bed_temp=85 profile=Contact. I've been getting the Toolhead stopped below model range and the Error during homing contact: Contact triggered while accelerating errors. The nozzle height looks normal when I get these messages.
18 replies
RRCRat Rig Community [Unofficial]
Created by millenford - VC4 300h on 10/3/2024 in #ratos-support
Is there a range of numbers I can or should increase to avoid these messages?
I've gotten this two or three times in just the last couple of days. Never saw them before.
3 replies
RRCRat Rig Community [Unofficial]
Created by millenford - VC4 300h on 8/13/2024 in #ratos-support
Getting occasional "mcu shutdown - timer too close" shutdowns.
I have many print hours now on the new SD card without shutdowns or timer too close errors, so I'm marking this issue as solved.
162 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
You know better than anybody, that there's a million things to keep track of. It's a huge challenge.
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
was NOT running
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
I'm glad you and 03Julian04 had this discussion, because that was my problem too. The contact mode was running in mine until I did that.
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
good.
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
No description
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
Well shit. I'll try that!
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
ok
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
I wasn't sure it would, but since it didn't give an error I thought it took it.
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
Won't take a smooth time value?
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
I thought it might be a long shot that the smooth_time var name was even recognized, but it didn't give me an error when I saved it.
923 replies
RRCRat Rig Community [Unofficial]
Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
So yes, after RatOS.cfg
923 replies