StrashaCZ
RRCRat Rig Community [Unofficial]
•Created by abcurrie on 7/9/2024 in #ratos-support
Realtime Analysis not working with BTT lis2dw card
absolutely understands. its nice to have. sure you have other priorities. 😉 But thanks for the great work, its a wonderful piece if work 😉
30 replies
RRCRat Rig Community [Unofficial]
•Created by abcurrie on 7/9/2024 in #ratos-support
Realtime Analysis not working with BTT lis2dw card
Is it in plan that it will be implemented also to the real time analysis?
30 replies
RRCRat Rig Community [Unofficial]
•Created by abcurrie on 7/9/2024 in #ratos-support
Realtime Analysis not working with BTT lis2dw card
Like realy? Cmoon. Stupid i am. Could have thought about it. Yes it worked! Thank you. :ratrig_heart:
30 replies
RRCRat Rig Community [Unofficial]
•Created by abcurrie on 7/9/2024 in #ratos-support
Realtime Analysis not working with BTT lis2dw card
30 replies
RRCRat Rig Community [Unofficial]
•Created by abcurrie on 7/9/2024 in #ratos-support
Realtime Analysis not working with BTT lis2dw card
30 replies
RRCRat Rig Community [Unofficial]
•Created by abcurrie on 7/9/2024 in #ratos-support
Realtime Analysis not working with BTT lis2dw card
Klipper hlásÃ: ERROR
mux command ACCELEROMETER_MEASURE CHIP None already registered ({'controlboard': <bound method AccelCommandHelper.cmd_ACCELEROMETER_MEASURE of <extras.adxl345.AccelCommandHelper object at 0xf5e9abc8>>, 'lis2dw': <bound method AccelCommandHelper.cmd_ACCELEROMETER_MEASURE of <extras.adxl345.AccelCommandHelper object at 0xf5f34310>>, None: <bound method AccelCommandHelper.cmd_ACCELEROMETER_MEASURE of <extras.adxl345.AccelCommandHelper object at 0xf5f34310>>, 'beacon': <bound method AccelCommandHelper.cmd_ACCELEROMETER_MEASURE of <extras.adxl345.AccelCommandHelper object at 0xf5e7dc40>>})
Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
30 replies
RRCRat Rig Community [Unofficial]
•Created by abcurrie on 7/9/2024 in #ratos-support
Realtime Analysis not working with BTT lis2dw card
@miklschmidt so lis2dw over USB to RPi is not supported at all? I am trying to at least get the input shaper (resonance tester) up and running on my V-Minion at RatOS 2.1. But no way i am able to make it run. I used old config style i used at RatOS 2.0 and nothing. It always trigered me error. If i select Beacon for X and none for Y, or adxl for Y (and change it to lis2dw) or beacon also for Y and change it.
30 replies
RRCRat Rig Community [Unofficial]
•Created by abcurrie on 7/9/2024 in #ratos-support
Realtime Analysis not working with BTT lis2dw card
Sorry to steal this chat, but i think same issue but on different HW.
30 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
No it does not. Well unless you will use just one screw out of those two for motor side. But i don't think it's that much needed. In this case I like the wobblex version because it will detach there.
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
two screws for each joint
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
this type. i have it from our czech supplier but its the same. https://www.amazon.de/-/en/SUOFEILAIMU-MI-Coupler-Coupling-Flexible-Diameter/dp/B095K2J8RM
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
With wobblex you have detaching place at the wobble so it's little bit more safe.
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
The bearing up there is not so rigid that it will stuck there. And I am not using the bearing there anyways. But I also don't use spider coupler. 😂
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
Yes that's Oldham mod I have and it's just about what type of coupler you have.
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
Don't turn on the heater if you will use fingers on nozzle. 😂😂😂
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
Well, I don't see such an issue with Oldham mod. 😉
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
Wtf?
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
Yes it is.
135 replies
RRCRat Rig Community [Unofficial]
•Created by migferlab on 9/19/2023 in #fix-my-print
V-minion z-wobble or banding
I still have little wobbling on my screw, but doest apply to the print. 😉
135 replies