WernerS
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
I received the new EBB42 and it worked initially. It seems I fried the previous one. However, after 15 minutes, it stopped working again (same issue) when I touched the nozzle (while it was off). I couldn't get it to work after that. I suspect it's due to ESD, as I had noticed some ESD shocks when touching metal furniture before. So, I bought another EBB42 and some ESD protection. I installed the new one, and it is working fine now. Has anyone noticed something similar?
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
also i do not measure an short. It measures 1088 ohm on the pins of the connector measured on the back of the boards. To me it seems only an broken board can be the cause. Lets see
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
i tried soldering the joints. But again no difference. I will order an new ebb42 to see what it does
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
i'm afraid i have an broken ebb42 as it was working and just stopped. I was changing the nozzle when it happened.
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
yep used the right pins.
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
just measured the PT1000 on the pins on back of ebb42 1088ohms. Seems fine
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
mabey the ebb42 board?
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
also tried 3 diferent PT1000 with no short.
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
yes i tried without pullop resistor entry and it made no difference
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 7/5/2024 in #fix-my-printer
PT1000 Temperature readout minus (-)225 degrees
hi and thanks
21 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/30/2024 in #ratos-support
Getting this error on each layer: Unknown command:"_ON_LAYER_CHANGE
Found it, Thanks again
9 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/30/2024 in #ratos-support
Getting this error on each layer: Unknown command:"_ON_LAYER_CHANGE
Thanks, but i do not know what or where to look.
9 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/11/2024 in #ratos-support
Consistent Verification Error When Flashing Image File to SD Card Using Etcher
with newwer no succes
26 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/11/2024 in #ratos-support
Consistent Verification Error When Flashing Image File to SD Card Using Etcher
Yes I finally got RatOs 2.02 working with Etcher 1.18.8
26 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/25/2024 in #ratos-support
4028 Inverted behavior on EBB42. Even with !fan_part_cooling_pin
Thanks for your time
34 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/25/2024 in #ratos-support
4028 Inverted behavior on EBB42. Even with !fan_part_cooling_pin
I will try tomorrow connecting directly to octopus .
34 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/25/2024 in #ratos-support
4028 Inverted behavior on EBB42. Even with !fan_part_cooling_pin
34 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/25/2024 in #ratos-support
4028 Inverted behavior on EBB42. Even with !fan_part_cooling_pin
I assumed that connecting the pwm wire to PA0 could work like with the VCore4
34 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/25/2024 in #ratos-support
4028 Inverted behavior on EBB42. Even with !fan_part_cooling_pin
then I understood it wrong.
34 replies
RRCRat Rig Community [Unofficial]
•Created by WernerS on 6/25/2024 in #ratos-support
4028 Inverted behavior on EBB42. Even with !fan_part_cooling_pin
not the PWM from the ebb42? (blue wire) and power from octopus?
34 replies