Steppe_Warrior Comments - Answer Overflow

Steppe_Warrior

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

This is very strange, as it doesn't effect everyone and second - it didn't happened before. I owned a much chipper printer and it didn't happen either. Also it started with RatOs 2.0

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

Thanks for pointing to your tread. I'm currently reading it but just curious, did you find the solution?

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 9/10/2024 in #fix-my-print

Ellis' Pressure Advance / Linear Advance Calibration Tool - not working on RatOS v2.1

I understand what you said, but this is not related to this. The files fails to print every time. Finally i managed to print it, manually delete all that i supposed is necessary in the file. Just curious, if anyone with a new software have similar problem with this file

13 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 9/10/2024 in #ratos-support

Move exceeds maximum extrusion (2.673mm^2 vs 0.640mm^2)

I will try this, thank you for a hint!

16 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

Printed a quick print with PTEG, and the final result was not bad, taking into account that no calibration was done for PETG. But i was away during the print and can not verify how the first few layers were printed.Will make some more test tomorrow. Also, the temperature parameters are almost the same for PTEG and ABS.

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

Because earlier i have never have this problem

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

I will try now to change filament to PETG and see what happens

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

I have read this somewhere in the past, but thought that it more related to adhesion, rather then to Z-height or Z-offset deviation\

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

How much time do you think pre-heating without active heater is enough before printing something?

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

I pressed pause and re-homed Z. After that resume print and the layers actually become printing normally. I have checked my Z axes screws and haven't seen something strange.

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

I have noticed that during the print, when it start print with low speed, lets say 60 mm/s, and i increased speed up to 300%, the extruder start slipping, but it looks like it is due to the fact that the print head is touching buildplate and make it hard for extruder to push filament through.

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

Have checked all screws and didn't find anything strange.

80 replies

RRCRat Rig Community [Unofficial]

•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print

And here we go again... first layer problem even with beacon3D

But still I can't figure it out if it is a carriage or the whole rail, that is moving.

80 replies

RRCRat Rig Community [Unofficial]