xrealx2024
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
Yes I did that.. but I think my flows are off as well.. the prints coming out of this rapido 2 are ass 😄
16 replies
RRCRat Rig Community [Unofficial]
•Created by JaminCollins on 9/6/2024 in #ratos-support
RatOS 2.x + Beacon ignoring configured offset and discarding offset at print end
Interesting.. I got mine to pass calibration.. but my print quality is not very good..
339 replies
RRCRat Rig Community [Unofficial]
•Created by JaminCollins on 9/6/2024 in #ratos-support
RatOS 2.x + Beacon ignoring configured offset and discarding offset at print end
What effect does the turning off of the thermal expansion? Does it let you adjust z?
339 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
16 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
How does the z offset work, if I read before it can be ignored dependent on heat coefficient?
16 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
So I kept testing, I tightened up parts (on z, the screws had some give).. it passed.. I do my first print.. its a bit low, but again it could be flow/extrusion rate might be too much... but it prints..
16 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
What if I run the test at lower temps? Just to see if it makes any difference?
16 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
Endstops? The x and y work. The beacon works until this point.. :S
16 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
I am now in performance mode as well
16 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
I have checked the z motors/coupler.. its as it should be
16 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
Arms are printed using ABS
16 replies
RRCRat Rig Community [Unofficial]
•Created by mazas on 9/1/2024 in #ratos-support
version mismatch, seems like a truncation issue?
It is indeed fixed.. Thanks miklschmidt!
14 replies
RRCRat Rig Community [Unofficial]
•Created by mazas on 9/1/2024 in #ratos-support
version mismatch, seems like a truncation issue?
I was getting the same issue.. I am glad its mentioned here
14 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 9/6/2024 in #ratos-support
MCU shutdown; timer too close
How are you powering it?
6 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
16 replies
RRCRat Rig Community [Unofficial]
•Created by JaminCollins on 9/6/2024 in #ratos-support
RatOS 2.x + Beacon ignoring configured offset and discarding offset at print end
Im unable to pass.. everthing is fine.. does the initial tests.. then at the end my sample sizes go to hell... and my latencies which were 1-3 at the start/middle all of a sudden are 4-6 at the end
339 replies
RRCRat Rig Community [Unofficial]
•Created by xrealx2024 on 9/7/2024 in #ratos-support
Beacon Rev H - Will not pass calibration. What is wrong?
In my case, I notice when everything is heated up.. my spread samples become too big..
16 replies
RRCRat Rig Community [Unofficial]
•Created by JaminCollins on 9/6/2024 in #ratos-support
RatOS 2.x + Beacon ignoring configured offset and discarding offset at print end
Looks like it..
339 replies
RRCRat Rig Community [Unofficial]
•Created by JaminCollins on 9/6/2024 in #ratos-support
RatOS 2.x + Beacon ignoring configured offset and discarding offset at print end
Jamin did you get it working?
339 replies
RRCRat Rig Community [Unofficial]
•Created by JaminCollins on 9/6/2024 in #ratos-support
RatOS 2.x + Beacon ignoring configured offset and discarding offset at print end
Jamin did you fix yours?
339 replies