guru-florida
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
I think I should be supporting the loom on the roof of the enclosure a bit.
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
yeah, the axis labels in the graph do not match physical axis but I just ignored that...I heard this doesnt matter...but I guess there is a way to remap the axis if it does.
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
I superglued the rear motor mount plastic to the standard loom mount. EBB just happened to fit the same holes as the stepper on that print hehe. It is solid, but I think the standard loom mount is not enough. I added some rubber tube there to strengthen it.
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
No change with OrcoSlicer changes. Found out after printing those settings aren't transmitted to gcode when output is set to klipper anyway.
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
I am trying to get a few new EVA parts printed so I can rebuild the toolhead with the Beacon probe and a proper EBB loom mount. I have my EBB42 mounted to a make-shift loom mount from spare printed parts. It's pretty solid but could be better and the hanging loom might be causing that bump >75Hz.
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
I had the "Motion Ability" tab in Orcaslicer with the accel set to 9000...and it is enabled to output those limits to gcode...so that should be changed to match the 6200. I am going to try another print with just those settings changed and see what happens to that ringing.
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
I can see where the tool head is pulling back after the 90 into the part so there is a vertical crevice. Weird.
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
What was your volumetric limit on the ASA filament?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
After hearing what you said about mfg, it's possibly it isn't dry enough. I had it in the dryer maybe 4 hours so far.
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
and 48v steppers
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
I have the vcore2 with a super lightweight gantry and aluminum Y mounts
56 replies
RRCRat Rig Community [Unofficial]
•Created by guru-florida on 9/17/2024 in #fix-my-print
Burn-through in ASA? What causes this failure?
ok great. I will try some of your filament settings too. I had 0.91 for filament multiplier after doing a flow test
56 replies