c00ki3 vc4 300 hybrid
c00ki3 vc4 300 hybrid
RRCRat Rig Community [Unofficial]
Created by Raven 3D Tech on 10/6/2024 in #ratos-support
Do you need to reflash your boards if you move to RatOS
@Raven 3D Tech RatOS doesn’t support canbus. The boards must be connected via USB. Connect your boards with USB a flash with configurator. You can modify RatOS with printer. cfg overrides. But with canbus it is your decision to make it work. For canbus there will be not official support.
5 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
👍
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
For dfu Mode no sdcard needed
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
It should Not take Long. Maybe 10-20 sec
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
Maybe your Board Accept only 8gb cards
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
Try this. Also try to rename the Firmware to Firmware1.bin
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
Can you try to power via 24 Volt or with a other usb Power?
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
The jumper for usb power in on the mainboard?
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
So the Firmware.bin does‘nt change to Firmware.cure?
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
Habe you done the Flashing with the sdcard according the Manual
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
How to you power the mainboard?
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
Or try another usb cable from the rpi to the mainboard
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
The Firmware is on the new sdcard?
44 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
Try Flash via Sdcard
44 replies
RRCRat Rig Community [Unofficial]
Created by Toilettentaucher on 9/4/2024 in #ratos-support
V Core-4 IDEX Klipper shutdown when trying to generate input shaper Graphs on toolhead 0
What adxl settings have you on the t0 toolhead. Maybe both toolheads must be ebb tollheadboard?
14 replies