Rigattoni
Rigattoni
PostsComments
RRCRat Rig Community [Unofficial]
Created by flat-fuchsia on 3/31/2025 in #german-support
Z-Tilt wird nicht richtig ausgeführt
Schau mal nach den Anschlüssen für die Y-Achse. Möglicherweise ist da ein Adernpaar vertauscht.
13 replies
RRCRat Rig Community [Unofficial]
Created by like-gold on 3/31/2025 in #german-support
Z-Tilt wird nicht richtig ausgeführt
Das kann ich dir nicht beantworten. Evtl. kann Helge da helfen?
13 replies
RRCRat Rig Community [Unofficial]
Created by inland-turquoise on 3/31/2025 in #german-support
Z-Tilt wird nicht richtig ausgeführt
Denke nicht, dass er ein Z-Problem hat, sondern da läuft ein Motor auf Y falsch herum. Siehe letztes Video der 3 oben.
13 replies
RRCRat Rig Community [Unofficial]
Created by Rigattoni on 3/5/2025 in #ratos-support
Second EBB42 toolboard: Not able to setup.
Well tried that first but with no luck... Tried the manual way as in the past before using RatOS... and failed too. I now used the configurator once again setting again to IDEX and chose fresh install. Now it worked as expected and the second EBB42 is recognized: 
pi@ratos:~ $ ls /dev/serial/by-id/*
/dev/serial/by-id/usb-Beacon_Beacon_RevH_02C709225154364134202020FF153432-if00
/dev/serial/by-id/usb-Klipper_stm32g0b1xx_btt-ebb42-12-t0-if00
/dev/serial/by-id/usb-Klipper_stm32g0b1xx_btt-ebb42-12-t1-if00
/dev/serial/by-id/usb-Klipper_stm32h723xx_btt-octopus-pro-h723-11-if00
pi@ratos:~ $ ls /dev/serial/by-id/*
/dev/serial/by-id/usb-Beacon_Beacon_RevH_02C709225154364134202020FF153432-if00
/dev/serial/by-id/usb-Klipper_stm32g0b1xx_btt-ebb42-12-t0-if00
/dev/serial/by-id/usb-Klipper_stm32g0b1xx_btt-ebb42-12-t1-if00
/dev/serial/by-id/usb-Klipper_stm32h723xx_btt-octopus-pro-h723-11-if00
5 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
Beside that... Back to the main issue: @za_naimis I would check that repaired EBB42. If it is not recognized at all and you are not able to flash that device, I expect a broken toolboard. The way to flash with RatOS is correct as written in https://github.com/lhndo/LH-Stinger/wiki/Pico-MMU-RatOS
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
I already posted it here: https://discord.com/channels/582187371529764864/859890291591217162/1344412507103563826
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
Yes, I know
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
What I wrote is, that the configurator page shows T0 even on the page for the T1. 😉
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
That´s completely right.
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
Exactly... but the TE is even not able to flash that device, It´s the plan to get it as T1. I expect that the repair of the USB did not go well.
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
Well, I already flashed 3 different EBB42 with RatOS in the configurator, just switching to IDEX and not storing anything. Works perfect on my side.
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
You wrote that you repaired the USB connector on the Pico EBB42... Are you sure that this EBB is working?
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
No, the toolhead has not been flashed. 
lrwxrwxrwx 1 root root 13 Feb 26 03:44 usb-Beacon_Beacon_RevH_890DA9F45154354D38202020FF0A082E-if00 -> ../../ttyACM2
lrwxrwxrwx 1 root root 13 Feb 26 03:44 usb-Klipper_stm32f446xx_btt-octopus-11-if00 -> ../../ttyACM1
lrwxrwxrwx 1 root root 13 Feb 26 03:44 usb-Klipper_stm32g0b1xx_btt-ebb42-12-t0-if00 -> ../../ttyACM3
lrwxrwxrwx 1 root root 13 Feb 26 03:44 usb-Beacon_Beacon_RevH_890DA9F45154354D38202020FF0A082E-if00 -> ../../ttyACM2
lrwxrwxrwx 1 root root 13 Feb 26 03:44 usb-Klipper_stm32f446xx_btt-octopus-11-if00 -> ../../ttyACM1
lrwxrwxrwx 1 root root 13 Feb 26 03:44 usb-Klipper_stm32g0b1xx_btt-ebb42-12-t0-if00 -> ../../ttyACM3
You only see Beacon, Octopus and one single EBB42...
23 replies
RRCRat Rig Community [Unofficial]
Created by za_naimis on 2/26/2025 in #ratos-support
toolboard device conflict
As I wrote... Both are shown as T_0, but the second one has another serial. This is what you need. Follow the steps I provided there.
23 replies
RRCRat Rig Community [Unofficial]
Created by Rigattoni on 5/25/2023 in #german-support
Chamber Heater
Das steht übrigens auf 1.0 um die Heizung zu unterstützen. Bringt halt Bewegung in die Luft im Drucker.
44 replies
RRCRat Rig Community [Unofficial]
Created by Rigattoni on 5/25/2023 in #german-support
Chamber Heater
Ja genau... das da raus kopieren und in die printer.cfg einfügen...
44 replies
RRCRat Rig Community [Unofficial]
Created by Rigattoni on 5/25/2023 in #german-support
Chamber Heater
Setze 
variable_chamber_filter_speed: 1.0 
variable_chamber_filter_speed: 1.0
doch auf 0.5 statt auf 1.0
44 replies
RRCRat Rig Community [Unofficial]
Created by Rigattoni on 5/25/2023 in #german-support
Chamber Heater
[gcode_macro RatOS]
variable_chamber_filter_enable: True                     # True|False = enable chamber filter control
variable_chamber_filter_speed: 1.0                       # float = chamber filter fan speed.
variable_chamber_filter_enable_at: "after_print_start"   # before_print_start|after_print_start|print_end = when to enable the filter
variable_chamber_filter_disable_period: 300              # int = disable fan after X seconds after the print ends
variable_chamber_filter_disable_bed_temp: 0              # int = wait for X°C bed temp after the print ends before disabling the filter
[gcode_macro RatOS]
variable_chamber_filter_enable: True                     # True|False = enable chamber filter control
variable_chamber_filter_speed: 1.0                       # float = chamber filter fan speed.
variable_chamber_filter_enable_at: "after_print_start"   # before_print_start|after_print_start|print_end = when to enable the filter
variable_chamber_filter_disable_period: 300              # int = disable fan after X seconds after the print ends
variable_chamber_filter_disable_bed_temp: 0              # int = wait for X°C bed temp after the print ends before disabling the filter
44 replies
RRCRat Rig Community [Unofficial]
Created by Rigattoni on 5/25/2023 in #german-support
Chamber Heater
https://github.com/HelgeKeck/RatOS/blob/documentation_v2.1/site/docs/configuration/chamber_filter.md
44 replies
RRCRat Rig Community [Unofficial]
Created by Rigattoni on 5/25/2023 in #german-support
Chamber Heater
...übrigens hier nachzulesen: https://github.com/HelgeKeck/RatOS/blob/documentation_v2.1/site/docs/slicers.md
44 replies