JimBill
RRCRat Rig Community [Unofficial]
•Created by JimBill on 1/27/2024 in #fix-my-print
Wavy patterns in vertical print surface V-Minion. Orcaslicer default profile PLA.
Shit nozzle was the cause. New Nozzle and I'm back to perfect prints.
4 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 9/5/2023 in #fix-my-printer
Ratos, Prusa Einsy MK3, homing moves right instead of left.
11 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 9/5/2023 in #fix-my-printer
Ratos, Prusa Einsy MK3, homing moves right instead of left.
here's the homing.cfg file. I'm assuming it's intentionally set to bump the right side. Either would work. I just happen to have a cable mess on that side at the moment.
11 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 9/5/2023 in #fix-my-printer
Ratos, Prusa Einsy MK3, homing moves right instead of left.
11 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 9/5/2023 in #fix-my-printer
Ratos, Prusa Einsy MK3, homing moves right instead of left.
this is out of RatOS's sensorless-homing-tmc2130.cfg defaults
11 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 9/5/2023 in #fix-my-printer
Ratos, Prusa Einsy MK3, homing moves right instead of left.
[stepper_x]
endstop_pin: tmc2130_stepper_x:virtual_endstop
position_endstop: 255
position_min: 0
position_max: 255
homing_speed: 25
homing_retract_dist: 0
[stepper_y]
endstop_pin: tmc2130_stepper_y:virtual_endstop
position_endstop: -4
position_min: -4
position_max: 212.5
homing_speed: 25
homing_retract_dist: 0
[stepper_z]
endstop_pin: probe:z_virtual_endstop
position_min: -5
position_max: 214
[gcode_macro RatOS]
variable_homing: "sensorless"
variable_sensorless_x_current: 0.4
variable_sensorless_y_current: 0.4
11 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 9/5/2023 in #fix-my-printer
Ratos, Prusa Einsy MK3, homing moves right instead of left.
I think this is the section I need to change if not Macros
11 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 9/5/2023 in #fix-my-printer
Ratos, Prusa Einsy MK3, homing moves right instead of left.
doubt it's wiring. Stock MK3s with Ratrig's MK3S profile.
11 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 9/5/2023 in #fix-my-printer
Ratos, Prusa Einsy MK3, homing moves right instead of left.
thanks. Looking. I'm not very familiar with Klipper. In Marlin, there was specific homing configuration. I'm not seeing a section like that in any of the RatOS files.
11 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 5/14/2023 in #fix-my-printer
I have a v-minion which has printed flawlessly until I started printing ASA - layer shift
no, haven't tuned PA for the ASA yet. I'd been printing fine without doing it.
5 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 5/14/2023 in #fix-my-printer
I have a v-minion which has printed flawlessly until I started printing ASA - layer shift
Thanks. 260 degrees for ASA. I've been using Orcaslicer. I also recently switched to a .6 nozzle (trianglelab).
5 replies
RRCRat Rig Community [Unofficial]
•Created by JimBill on 5/14/2023 in #fix-my-printer
I have a v-minion which has printed flawlessly until I started printing ASA - layer shift
Also, this has been happening in a heated chamber. My perfect prints, even with small ASA objects, were without an enclosure.
5 replies